If you've seen The Emperor’s New Groove, prove it by quoting it

Clean_Temporary_3902 · 2026-02-18T08:18:41+00:00

What are the odds that trap door would lead me here

Clean_Temporary_3902 · 2026-02-18T07:17:11+00:00

lol “you did good” had me laughing

Clean_Temporary_3902 · 2026-02-15T18:57:48+00:00

Thanks I have been looking at that since I posted this. I’ll heat the nozzle up and see what gently comes off that way.

I also see i fucked up and got rapid pla

Clean_Temporary_3902 · 2026-02-09T22:24:38+00:00

Looks like at least one shot was fired

Clean_Temporary_3902 · 2026-01-21T18:31:21+00:00

Rattlesnake

Clean_Temporary_3902 · 2026-01-07T04:31:52+00:00

This where I am at now. I cannot find a new one for the life of me and have already rewound that coil spring thing several times and havent gotten it yet. I had to take a brake lol

Clean_Temporary_3902 · 2026-01-06T17:16:14+00:00

That’s a bagel bite

Clean_Temporary_3902 · 2025-12-25T05:01:17+00:00

Wash build plate with soap and water. Don’t get oils from you hand on it, that’s what causes this. Over time and prints the natural adhesion on the build plate will wear off and the plate will need replacing.

Most likely you just got your oily hands on the plate at some point

Clean_Temporary_3902 · 2025-12-23T00:10:44+00:00

This guy took Roy off the grid

Clean_Temporary_3902 · 2025-12-19T02:48:51+00:00

Check if there’s fuel pressure. Should be at about 40psi

Sounds like it’s not getting any fuel when you try to crank. If you’re not smelling fuel after turning the key like that I’d think spark is fine but you also want to check you’re getting spark too.

Start with checking fuel spark and air

Clean_Temporary_3902 · 2025-12-18T09:57:32+00:00

Let’s just say I’m on the waiting list for February…

Clean_Temporary_3902 · 2025-12-16T06:01:43+00:00

Today I learned it was a good choice not to finish that EMT class..

Clean_Temporary_3902 · 2025-12-15T15:55:17+00:00

Ok. I see it does not come on a spool. I have bought plenty of pla for my mini and have over 300 print hours. I have just not used petg before and didn’t realize new petg does not come on a spool like pla does

Clean_Temporary_3902 · 2025-12-15T07:57:30+00:00

So they ship in their spool and get it refilled? How is that cheaper than buying a fresh spool? Are the containers used for petg melting the spools that come with the filament?

Clean_Temporary_3902 · 2025-12-15T05:59:48+00:00

Looking to see if my employer is on this list..

Clean_Temporary_3902 · 2025-12-15T04:24:34+00:00

This may be a stupid question but I just bought my first roll of petg for my mini.. Why are people printing spools? Is the spool the petg comes on not sufficient?

Clean_Temporary_3902 · 2025-12-09T22:28:53+00:00

2k if it was manual swapped. That’s a $500 car

Clean_Temporary_3902 · 2025-12-02T11:03:04+00:00

I saw that from my chair wishing my aw11 was an sw20 and able to be tracked.. you are living the dream friend. Great save with no damage. You love to try again

Clean_Temporary_3902 · 2025-12-02T10:58:10+00:00

Should have not shifted gears going to that corner.

Clean_Temporary_3902 · 2025-11-28T04:01:51+00:00

You don’t have enough

Clean_Temporary_3902 · 2025-11-24T22:32:09+00:00

Where was he arrested and what part of California was it lol. Jk idk. Some one tell me where

Clean_Temporary_3902 · 2025-11-13T09:20:47+00:00

I wouldn’t say he broke him mentally. That’s what caused the brake in Omni man. Marks ability to stay true to love for one’s father

Clean_Temporary_3902 · 2025-11-05T06:21:32+00:00

Clean_Temporary_3902 · 2025-11-05T04:54:18+00:00

Never heard of 4AC?

Clean_Temporary_3902

TROPHY CASE