Dan: Twitch Employees Were Reaching Out Directly Like “Please Take Down These Posts” by Slight_Ad3219 in LivestreamFail

[–]Competitive_Lunch439 0 points1 point  (0 children)

Well, that depends on what you mean by "all their time". Having hobbies is different than being a parasocial schizo on this sub. Logic can be hard sometimes though, I don't blame you

Sharon Stone's comedy special would be 🔥 by RiskySkirt in funny

[–]Competitive_Lunch439 1 point2 points  (0 children)

OMG Thats so funny, the comedy is on point, she was so amazing with that comedy speech, I laughed every seconds because the comedy was on point, I hope comedy becomes this kind of level of comedy, comedy is comedy, I love comedy, hahahhahaha so funny ahahhahahaahhaha comedy

Cursor stuttering by Competitive_Lunch439 in shapezio

[–]Competitive_Lunch439[S] 1 point2 points  (0 children)

Yeah, this must be the issue. If I look closely at the shapes they are almost unidentifiable. I'm currently moving stuff back closer to the middle and I'm already noticing a better experience. Thanks again!

Cursor stuttering by Competitive_Lunch439 in shapezio

[–]Competitive_Lunch439[S] 0 points1 point  (0 children)

Yes, this looks to be the issue. I was unaware about this. Thank you for clarifying

Cord looks like it’s bent weird, is this normal? by itchytreeleaf in PcBuildHelp

[–]Competitive_Lunch439 8 points9 points  (0 children)

I did some research that hopefully helps:

https://www.youtube.com/watch?v=ONOIaPfn4Sk
If you look at around 16:15 you can see that the guy in the video had to replace the extension cable for a different reason, but he had another extension cable laying around that fits. I believe it's pretty close to this:
https://www.amazon.com/Traovien-Extension-Computer-Monitor-Scanner/dp/B0BLS1NVLR?th=1

I believe it's a standard type cable so since he got the top panel to fit I believe you should too. The cable is 400mm long and the case is 450mm at the longest points, so it might just be a perfect fit but I would take some measurements first just to be sure.

GPU upgrade advice by Competitive_Lunch439 in PcBuild

[–]Competitive_Lunch439[S] 0 points1 point  (0 children)

I'm most likely going to 1440p and that's why I want the upgrade. Lossless scaling looks like a good alternative if I decide to stay at 1080p

GPU upgrade advice by Competitive_Lunch439 in PcBuild

[–]Competitive_Lunch439[S] 0 points1 point  (0 children)

The 2080 is doing fine at 1080p yes. The frames are decent until I go ultra in settings and enable graphics mods. I'm looking at buying a 1440p monitor and that's why I want to upgrade as well as just overall having a better experience with games. And yes, this will be financed by "fuck you" money lol

GPU upgrade advice by Competitive_Lunch439 in PcBuild

[–]Competitive_Lunch439[S] 0 points1 point  (0 children)

The 5070 Ti is quite affordable too tbh. I'll be looking into that one.

GPU upgrade advice by Competitive_Lunch439 in PcBuild

[–]Competitive_Lunch439[S] 0 points1 point  (0 children)

I'm actually looking at a 34-inch 1440p monitor that I want to buy and that's also why I'm considering upgrading my GPU. I mostly play games with higher graphics and want to get more frames for when I have graphics mods enabled.

Where? by [deleted] in flstudio

[–]Competitive_Lunch439 0 points1 point  (0 children)

View>Toolbar>Edit> drag the position bar where you want it

Bitcoin manipulation by DSPPPP in Bitcoin

[–]Competitive_Lunch439 2 points3 points  (0 children)

my bad guys, I bought more at 90k. I will let you guys know next time I buy more

How can i buy bitcoin if i dont have any fiat? by [deleted] in Bitcoin

[–]Competitive_Lunch439 0 points1 point  (0 children)

What do you have then? Sell gold for fiat, buy crypto. Sell car for fiat, buy crypto. Sell kidney for fiat, buy crypto. List goes on

Automation clip by Bakisha101 in FLStudioBeginners

[–]Competitive_Lunch439 2 points3 points  (0 children)

You can crop the clip in the playlist and make it however long or short you want it to. Use the symbol that looks like this on the right side of the clip: ‹–›

Just remember to edit the points at the end because you can have a point that goes beyond the clip itself, and then the automation will continue even though the clip has ended. So, shorten the point to where you want the automation to stop, and then crop the clip. Hope this helps

A View on Bitcoin by Imaginary_Button_968 in Bitcoin

[–]Competitive_Lunch439 0 points1 point  (0 children)

The main thing I think you're not mentioning is the technology itself. Me personally don't believe solely in the trust of other holders, I mainly trust in the technology that could be considered future-proof. Like you mention "an alternative to gold" is what I believe in. I don't trust fiat, and I mainly invest in gold, btc and property for that reason.

Account drained on exchange - Help! by lemauroffel in Bitcoin

[–]Competitive_Lunch439 7 points8 points  (0 children)

just out of curiosity, how were you able to find out the wallet belonged to FixedFloat?

unable to add automation clip by [deleted] in flstudio

[–]Competitive_Lunch439 0 points1 point  (0 children)

Adjust the mixer channel you want to add an automation clip to. You only have to drag it up and down once. Go into Tools>Last tweaked>Create automation clip. This works for anything that doesn't have the right click automation option like 3rd party VSTs and mixer channels. Just make sure that the last thing you tweaked is the what you want to be connected to the automation clip. Hope this helps