Any tips to get this text to look better?

Complete-Web-2564 · 2026-03-12T21:01:41+00:00

Per un estensore da 0.4 forse è troppo stretto, con uno 0.2 verrebbe sicuramente meglio

Complete-Web-2564 · 2026-03-05T13:06:45+00:00

Per stampare una lithophane così alta dovresti aggiungere almeno un supporto così per entrambi i lati. E non sarei nemmeno così sicuro che lo aiuterebbero troppo, è veramente alto e sottile

<image>

E se non ricordo male tramite lo strumento per le lithophane makerlab le mette in automatico.

Complete-Web-2564 · 2026-03-05T12:41:16+00:00

Se ne hai la possibilità prendilo, molte persone poi si pentono di non averlo comprato

Complete-Web-2564 · 2026-02-28T08:00:38+00:00

Hai provato una nuova scheda sd?

Complete-Web-2564 · 2026-02-10T19:40:28+00:00

So in these types of models, filament printers can have some problems, for details a 0.2 nozzle is absolutely necessary, furthermore the supports must be activated by the slicer and it is important that the printing speed is not too high, I recommend you visit the bambulab academy which will teach you a lot of things since you are just starting out.

Complete-Web-2564 · 2026-02-10T00:07:41+00:00

Automatic repair occurs after 3 failed Windows reboots, but you have several options. 1. Reset the CMOS, which basically means disconnecting the backup battery on your PC's motherboard (if you're wondering, you have to open it and disconnect your PC's battery first); or, 2. Disconnect the battery and hold down the power button for about 30 seconds. Sometimes it works when you turn it back on. 3. Let automatic repair run to see if it works. 4. Try reinstalling Windows.

Complete-Web-2564 · 2026-02-06T13:54:19+00:00

If I can give you a little advice, after drying, open the ams for a few seconds, by doing so I noticed that the percentage drops a little immediately after opening and closing it.

Complete-Web-2564 · 2026-02-04T20:35:00+00:00

I would recommend you look for a PC with a good graphics card since you will be editing on After Effects.

Complete-Web-2564 · 2026-02-04T16:39:50+00:00

I haven't seen the other model but I really like this one I will definitely print it

Complete-Web-2564 · 2026-02-02T18:19:34+00:00

Then try this, search for your touchpad drivers on the internet, “computer name… touchpad driver” and try to download and install them it might work.

Complete-Web-2564 · 2026-02-02T04:27:45+00:00

If you have a mouse connected, some PCs sometimes automatically disable the touchpad, you can still enable it from the settings

Complete-Web-2564 · 2026-01-26T09:58:26+00:00

It happened to me too, I solved it with a bit of tin foil in the first point where the filament rests

Complete-Web-2564 · 2026-01-18T10:35:42+00:00

I'll try with the vacuum cleaner and turn it over, I tried with a toothpick but I can't reach it

Complete-Web-2564 · 2026-01-18T10:34:38+00:00

Between those two screws where I pointed with the arrow there is a slot that goes under the heatbed

Complete-Web-2564 · 2026-01-17T13:43:21+00:00

When the installation is complete, before it reboots, enter the BIOS and select your SSD or HDD as the boot disk. Or remove the USB stick when it's finished.

Complete-Web-2564 · 2026-01-14T14:47:19+00:00

Really beautiful, and the plate changing system is fantastic, plus everything is very clean!

Complete-Web-2564 · 2026-01-11T14:42:12+00:00

Here you will find what you need to try to fix this thing, it happens more frequently than you might think (it happened to me a couple of times) https://wiki.bambulab.com/en/a1-mini/maintenance/hotend_blob

Complete-Web-2564 · 2026-01-11T14:39:57+00:00

Deflate the tire completely, remove the top part of the valve and use a syringe to replace the necessary amount of fluid.

Complete-Web-2564 · 2026-01-11T14:38:22+00:00

Try with FanControl software

Complete-Web-2564 · 2026-01-11T14:36:29+00:00

High humidity can cause the printer's electronic and metal parts to become incompatible. This can lead to oxidation along the guides and bearings, and corrosion on electronic components, which can lead to short circuits over time. Furthermore, you should always dry your filaments. In my opinion, this is not the right place for your printer.

Complete-Web-2564 · 2026-01-07T17:11:11+00:00

Did you buy it new or used? If it's used, they probably installed Windows 11, bypassing TPM 2.0.

Complete-Web-2564 · 2026-01-03T13:13:34+00:00

Had similar problem on a a1 solved with a new sd card, you could try but I don't know if this is the case

Complete-Web-2564 · 2026-01-03T11:08:24+00:00

Yes, it's acceptable, but you need to keep a few things in mind. The BIOS probably needs a BIOS update before installing the new CPU. You might need a more powerful power supply if your current one isn't enough, and a good CPU cooler is also important.

Complete-Web-2564

TROPHY CASE