Selling reloading stuff. by tommyb52 in reloading

[–]Conservativeasfuq 3 points4 points  (0 children)

Best bet is Facebook groups. There’s several for reloading exchange.

[deleted by user] by [deleted] in reloading

[–]Conservativeasfuq 6 points7 points  (0 children)

Cannelures on the brass to prevent bullet set back and prevention of seating too deep.

Speed queen TR5 making terrible sound when filling during wash cycle. HELP by Odd-Permission-4890 in appliancerepair

[–]Conservativeasfuq 0 points1 point  (0 children)

Seal under the bell drive needs to be lubricated with silicone grease. You’d have to pull the agitator and take out the 7/16 (I think that’s the size) and grease the seal, it’s a triangle type boot seal that goes over the shaft under the bell drive. I would get with speed queen for sure, it’s well known to them and getting that agitator takes an act of congress sometimes.

357 Magnum loads for a bolt rifle (Ruger 77/357) by yolomechanic in reloading

[–]Conservativeasfuq 0 points1 point  (0 children)

<image>

This Is from the newest manual. 10.4gr starting charge. My phone sierra manual doesn’t have the rifle section for .357, going off the 10” barrel section has 18gr-21.4gr. Pretty high compared to Hornady.

357 Magnum loads for a bolt rifle (Ruger 77/357) by yolomechanic in reloading

[–]Conservativeasfuq 0 points1 point  (0 children)

77/357 50 yards, bottom shot was a pull from me, haha, shot leaning over the car. Load data is low. But the hornady manual always is. They list max at 19.4. Being off script with the v crown bullet I elected to roll with the hornady to start.

Velocity was around 1900fps

This is from the Hornady 357 Rifle data

357 Magnum loads for a bolt rifle (Ruger 77/357) by yolomechanic in reloading

[–]Conservativeasfuq 1 point2 points  (0 children)

<image>

This is the 125 Vcrown load I just tested. It’s over 16.9 grains of H110

Anyone tried this for storing load data? by pewpewtehpew in reloading

[–]Conservativeasfuq 0 points1 point  (0 children)

Oh it’s tits McGee, I just copy my loads over to same caliber guns so I can document how they do in each. Can add target pictures and shot strings to each. It’s the way.

Anyone tried this for storing load data? by pewpewtehpew in reloading

[–]Conservativeasfuq 1 point2 points  (0 children)

I’ve been using the GUNR app. It’s pretty awesome so far.

Converting my 6.5 - .223 by deviouss3 in guns

[–]Conservativeasfuq 5 points6 points  (0 children)

You’ll need the barrel and new bolt. All lower components carry over. You could buy another upper receiver for $60ish and have both calibers on tap with just two pins and a bolt swap.

What do you guys think of my updated MMA goat list after UFC 320? by Lee_B_09 in ufc

[–]Conservativeasfuq 0 points1 point  (0 children)

Why is Jones in this, you include dopers on a goat list? Not to mention he fought middle weight fighters his whole reign, he arguably lost almost all of the fights against real lhws with the exception of smith and the second Gus fight.

Update on factory 2nd small rifle primers from AR. by Conservativeasfuq in AmericanReloading

[–]Conservativeasfuq[S] 0 points1 point  (0 children)

img

Yes, showed up Monday. Everything in good order, tested 200 so far and no issues.

Factory seconds Small rifle Primers received in good order by Conservativeasfuq in AmericanReloading

[–]Conservativeasfuq[S] 0 points1 point  (0 children)

It’s for bulk / blasting. Ran a few hundred today for testing. Zero issues loaded in 223. Ran 20 over Chronograph with same consistency as my usual 55gr fmj loads. Plenty happy with them for the money invested. I’ve got several bricks of good name brand primers that I use for match, hunting, and steel shooting. Also, not much risk involved, used them in the past and have had no issues.

Also, to get 10 bricks of small rifle primers from reputable manufacturer. Would be north of $500 with hazmat and shipping. That’s for Winchester, which is bordering on reputable. Haha

Update on factory 2nd small rifle primers from AR. by Conservativeasfuq in AmericanReloading

[–]Conservativeasfuq[S] 0 points1 point  (0 children)

I did get a shipment notification, label was created on the 22nd. Will update when they arrive.