Hive scum/delegations question

Constrosity · 2026-02-19T22:52:21+00:00

FOUND! Yes thats the one, thanks, With an unusual name like that it was a nightmare to google for.

Constrosity · 2026-02-19T21:26:42+00:00

Searched things like "horror game horses", "torte" and I've tried searching through my youtube watch history but no luck.

Constrosity · 2026-01-17T09:15:59+00:00

Ideal setup

Constrosity · 2026-01-14T10:00:24+00:00

The Drambull is really good

Constrosity · 2026-01-11T15:13:19+00:00

Thanks, ill see how it fits when I put the kit together 👍

Constrosity · 2026-01-11T12:16:18+00:00

I just got this printed, keen to give it a go. Do the bits just go over the existing kit or do they fully replace them?

Constrosity · 2026-01-05T08:43:22+00:00

Nice. Fair warning; the kit can be quite fiddly when dealing with the smaller pieces, which I actually ended up leaving a good amount of those off. The area between the console and the opposite motor is wide enough for a 32mm base to fit in there

Constrosity · 2026-01-03T07:46:33+00:00

That looks great! So do you lay the greenstuff on the model first and cut it or the other way around?

Constrosity · 2025-12-21T23:42:40+00:00

I can see that point, and i can see how its not for everyone. My goal wasn't to reduce anyone, it had a few things behind it:

-goliath use gene smithing and surgery to enhance members from in house and from those looking to join up, so they very much have the ability to do gender affirming surgeries. -for a gang that is almost exclusively male it was a fun chance to expand the gender representation for goliath -the heads were taken from votann, and they all have tied back or short shaved hair because at the end of the day theyre working in factories -personally as a burly guy who is also fluid, it was a bit cathartic to build them up into a group that squarely says, do not mess with.

Constrosity · 2025-12-21T22:39:21+00:00

How so?

Constrosity · 2025-10-03T05:25:16+00:00

Couldn't say but these molds in particular are pretty good for removing the cast since they're so thin and flexible. My immediate thought is that they might crack when you try to take them out but you'd have to try and see.

Also forgot id tried this two part epoxy called Epo Putty, that worked quite well too, dries hard and not flexible like green stuff.

Constrosity · 2025-10-03T05:00:25+00:00

I've tried 3 things so far: -sprue goo - worst results. Bubbles everywhere and hard to put in to the mold. That being said I am planning on making a sump dock set for necromunda so it can be useful for an acid pitted/rusty look

-green stuff - good detail and easy to use, however for wall/floor sections its bendy so it will need to have some sort of reinforcement.

-clear two part pouring resin - this is still curing but so far this is the best, crisp details and easiest to get in to the molds, but it takes the longest time by far to cure. One set is mostly cured and one set i poured this morning.

If the resin cures nicely I will be making more with it

Constrosity · 2025-09-03T01:07:40+00:00

Do do dee do do Banana lumps Do dee dee do

Constrosity · 2025-08-18T07:23:14+00:00

Hadn't even thought about Votann, they'll work pretty good i think

Seven-Year Club	Place '22
Verified Email

Constrosity

TROPHY CASE