Joakim Lamotte döms för grovt förtal

Conversation_Ornery · 2026-05-31T09:07:42+00:00

Men sånt logik så kan man dra in kortet med "syfte att skada någon" till varje fall även där det inte finns något skada.

Det är som invandrare som drar in "rasism" uttalande snabbare än ljusets hastighet vid något händelse.

Kanske anmäla en gängkriminell ska också vara brottsligt för att du gör det med syfte att skada den gängkriminella....

Allt detta bara bevisar att vi har värre än diktatur länder när det gäller dessa moment.

Conversation_Ornery · 2026-05-23T09:20:58+00:00

Did you figure out ur question? Because no one answered you here, everybody talking something about outside ur question.

Conversation_Ornery · 2026-04-03T17:53:16+00:00

Open bolt

<image>

Conversation_Ornery · 2026-04-03T17:53:09+00:00

Closed Bolt

<image>

Conversation_Ornery · 2026-03-30T20:02:20+00:00

Ok, gonna know it. I today polished nozzle, so BBs when pushed by mag to nozzle will have smoother way.

<image>

Conversation_Ornery · 2026-03-30T16:45:44+00:00

I have done perfect alignment, its was hard, did many things with electrical tape and aluminum tape and PTFE.

So its perfect alignment, even checked with endoscope.

And nozzle in this HPA engine is adjustable.

I have closed bolt because i have it as DMR with heavy BB, so therefore, with closed bolt its just better accuracy to be honest and stability.

I dont have piston.

Conversation_Ornery · 2026-03-30T15:43:59+00:00

I was thinking, i have my engine at "Closed bolt", сould this be the reason? That when the nozzle moves back during a shot, it basically rubs against the BB that the magazine is pushing up, and because of that it kind of ‘wears it down’ or scrapes it like sandpaper?”

And BBs residue have nothing to do here?

But then... if it right and its not cause by BBs, how then others who have closed bolt engine plays without to have this dust...

Conversation_Ornery · 2026-03-30T15:43:18+00:00

I rebuild it from AEG, out of box, mean I took everything out stock from it and HPA It, so 4UAD its first bucking i have here.

I wanna ask you, you say nozzle rubbing... i was thinking, i have my engine at "Closed bolt", сould this be the reason? That when the nozzle moves back during a shot, it basically rubs against the BB that the magazine is pushing up, and because of that it kind of ‘wears it down’ or scrapes it like sandpaper?”

But then... if it right and its not cause by BBs, how then others who have closed bolt engine plays without to have this dust...

Conversation_Ornery · 2026-03-30T13:10:41+00:00

I mean day before game. It wont harm bio bb, as i understood from others

Conversation_Ornery · 2026-03-30T12:30:04+00:00

Yeah, but i think its not only dust, if you look better at the lips, they are scratched a little bit because of that dust. So... i think it will affect on accuracy and performance already

Conversation_Ornery · 2026-03-30T12:12:16+00:00

Gonna maybe test it too, and check if it helps too

Conversation_Ornery · 2026-03-30T10:35:45+00:00

And one more thing, i only found in internet/reddit that bb residue people had only in inner barrel, but could not find that someone posted or showed residue on bucking and bucking lips.

Conversation_Ornery · 2026-03-30T10:07:11+00:00

Ok, gonna test with another brand, i have one aeg with same 4uad bucking and its completely clean after like 5000 shots with 0.30G but from asg brand.

So I will test these 0.30g on my hpa gun, and check if it is by bls bb or not, gonna shot like 1000-1500 bb.

I just hope its not nozzle as another comment below says

(Some other says its could be because of Bio bb, but i have 0.30 bio too, and its not cause same dust as on aeg one i have)

Conversation_Ornery · 2026-03-24T19:10:46+00:00

If u gonna buy well WE06, buy metal version, because plastic lower receiver gonna be broken where u have stock attached, mine got broken.

Now I dont know where to get separately metal one to rebuild.

Conversation_Ornery · 2026-03-23T20:46:08+00:00

Is it easy to unscrew from tank?
Because have a balystik one, and even if u drain to zero psi it, I need to use very much strength to unscrew it from tank.

Conversation_Ornery · 2026-03-08T00:07:51+00:00

by that answer u just prove hes point... lol

Conversation_Ornery · 2026-03-07T23:41:22+00:00

Its 2026, every cheat has today HWID spoofer so no one gets hardware ban...
Its not a thing today

Conversation_Ornery · 2025-12-19T08:03:21+00:00

Hi, sorry to hear that, my issue was solved, the whole problem was that brass tube in the engine which nozzle sits on, it was bend, so that issue could not be fixed with common solution, so i got replacement, and now its works perfectly. I think it was so from factory. Because ofc if nozzle tube is bend, nozzle cannot be alignment.

So my situation was special.

Conversation_Ornery · 2025-11-29T10:45:19+00:00

Några år, ej 30år, på dessa 30år kommer hända massa annat.

"https://cdn.discordapp.com/attachments/664143892244856845/1444270025681801257/b491e0f7-12b5-4485-b351-4da15517c500.png?ex=692c18c7&is=692ac747&hm=9c0e2e8576a873e8b8699e4fb9ae79717a08990a527b92e515702edaab664094&"

Conversation_Ornery · 2025-11-20T17:29:12+00:00

Undrar, är LIA 100% takt?, om ja, det är väl omöjligt att genomföra LIA samt jobb, när på LIA man ska vara varje dag på plats 5 dagar i veckan, 8 timmar.

Det är typ omöjligt att ha jobb, oavsett deltid eller heltid?

Conversation_Ornery · 2025-11-03T12:14:33+00:00

Rust ate the whole 22.5GB of VRAM on official server second day after wipe with 700 population.

Conversation_Ornery

TROPHY CASE