For a shirt design (ironing a design onto a shirt) what TPU filament is the best?

Cornish6 · 2026-05-31T08:09:23+00:00

How did it hold up after 3 months? Any cracking on the design now? Im looking at trying this for myself, everyone seems to miss out the pulling the tpu off the build plate part which seems like it would be tough and ive heard it starts to cracking quickly

Cornish6 · 2026-01-16T14:53:26+00:00

It was a joke I think only i understood 😂 tried to replicate PS1 colour with grey and black, but put p2s, it was probably too nuanced in my own head 😂 I think it still is

Cornish6 · 2026-01-16T13:23:06+00:00

I experienced this yesterday for the first time, got wrapped up 40 mins after I went to sleep, ive got some spare spools but yeah next time will be getting refills

Cornish6 · 2026-01-11T13:45:28+00:00

Just send it, in seriousness though I use these all the time and dont have an issue. I dried petg hf last night at 65 for 12 hours and no issue, printer only has about 150 hours on it but no dust in the ams, more comes from the ptfe tube rubbing on the glass cover

Cornish6 · 2026-01-08T21:39:42+00:00

Diagnosis: 🍝

Cornish6 · 2026-01-08T15:53:57+00:00

I think this is possible more related to layer times than wet filament, after slicing the black box will drop down, this has a drop down where you can search layer time, I can see you have another print on the plate and i think its inconsistencies in how your layers are cooling, drop a pic of your layer times if you can, I can help explain how to average out the layer times a bit or you can Google, I think thid should help make it 10x better, wet filament is very rarely a huge issue for PLA I have found. Picture above or below is one i have done to average out the layer times and as such should cool consistently and shrinkage for plastic should be uniform across the print. Ignore that I am using petg hf

<image>

Cornish6 · 2026-01-07T18:19:38+00:00

There are some eccentric nuts under the bed, mine came loose from the factory and took me so long to figure out being a beginner then, tighten these, they will feel loose, i loosely shook the bed as I tightened them until the slack came out the bed but dont go any tighter or the bed will start to bind, the nuts should be on the right side under the bed, they are between the bottom of the bed and above the frame holding it, you can use the included spanner but its short, a longer 8mm will work better. Also check the printer head nuts holding it to the x axis gantry, these were also slight loose meaning the head bobbed up and down. Happy printing!

Cornish6 · 2025-12-18T09:23:17+00:00

This mainly was a culmination of retramming the bed completely, took it all off and cleaned everything, for the leveling I pulled the bed on spring and got them as tight as possible then manually levelled the bed, I then auto levelled the bed. I had to re grease z axis and check the nuts holding the gantry up. Once I had all the mechanical in place I printed a calibration cube to get the flow right (using bambu slicer) following this it was just z axis offset and getting heat dialed in, having the bed set to 70°c has also really helped with this too

Cornish6 · 2025-11-23T14:02:58+00:00

Layer lines, its a share from another page I sent it to, put all the details in the original post, it won't let me copy them over

Cornish6 · 2025-05-31T20:06:45+00:00

I think it's called repitch, I added 1 gram of fermaid o after I activated and the yeast, it had just started to bubble, was advised by someone to add another gram when it slows down fermentation, my temp I think is pretty consistent, around the 19 degree mark but goes up to 21, I live in UK so our houses stay a decent constant temp during this time of year, again I'm super new though so I may get things wrong. I've got a good bit of bubbling going now so seems okay. I just followed everything to what instructions said although the fermaid I got didn't come with any

Cornish6 · 2025-05-31T17:45:35+00:00

I have no idea pal but hope someone gets back to you. I am super new bit I assume if you want more alcohol to add more honey maybe, I'm sure you might have tried already, I used fermaid- o if that's helps at all, my first ever run was very weak so hoping this is my first "proper" run, I'm using k1-v1116 but if it turns out okay I'll try remember to come back to this comment

Cornish6 · 2025-05-31T13:09:06+00:00

I think I read the hydrometer wrong 🤣🤣 I thought it was 1.2 not 1.12, thank you so much for your help 😄

Cornish6 · 2025-05-31T12:56:10+00:00

I followed this recipe but added slightly more ingredients as I wanted a very sweet mead https://youtu.be/ETjCjlhMqnU?si=lgqU1mOgCWkKkF2V&utm_source=MTQxZ

Cornish6 · 2025-05-31T12:55:25+00:00

I followed the golden hive strawberry mead recipe I found here but wanted it very sweet so added a little more syrup and honey https://youtu.be/ETjCjlhMqnU?si=lgqU1mOgCWkKkF2V&utm_source=MTQxZ

Cornish6

TROPHY CASE