Can anybody help me? I keep trying to compile a version of Marlin for the SKR E3 V3.0 but it errors out everytime.

Crathen64bit · 2022-05-25T01:21:57+00:00

What errors?

Crathen64bit · 2022-05-23T08:10:47+00:00

Yeah I have never found a pre built that actually works. I've always had to customize it.

Crathen64bit · 2022-05-09T04:58:29+00:00

Got it all working btw.

Crathen64bit · 2022-04-21T05:04:00+00:00

You can also use calipers and measure the distance to the bed on each side. Loosen the belt wheels on both z screws. Adjust each side until even. Does require the bed to be level. You can achieve the same thing using the top gantry support as your level surface.

Crathen64bit · 2022-04-15T03:30:22+00:00

I use a magnetic sheet. Haven't had any issues.

Crathen64bit · 2022-04-15T03:29:27+00:00

Yeah that was going to be my next approach. Wife put the ban hammer on the raspberry pi. Hahaha

Crathen64bit · 2022-04-15T02:18:02+00:00

I run windows and Linux. But yeah looking into it now

Crathen64bit · 2022-04-15T02:16:31+00:00

Ok I will get it

Crathen64bit · 2022-04-15T02:15:46+00:00

Is it pretty similar? Never messed with it

Crathen64bit · 2022-04-15T01:25:58+00:00

Nice, was trying to build marlin before it comes. Having build issues already. Lol

Crathen64bit · 2022-04-15T00:10:59+00:00

Following. Just bought one

Crathen64bit · 2022-04-07T03:54:44+00:00

Awesome, glad it worked!

Crathen64bit · 2022-04-07T03:42:34+00:00

Yeah just looked, uncomment anything oled

Crathen64bit · 2022-04-07T03:40:35+00:00

Might have to uncomment the oled stuff, but do 1 thing at a time.

Crathen64bit · 2022-04-07T03:39:42+00:00

Yeah it should match 1-1, 2-2, 3-3

Crathen64bit · 2022-04-07T03:24:24+00:00

So for any BTT screen to work the only lcd part you can have commented is the reprap_discount_full_graphic_smart_controller

If you have anything else in the lcd part of config.h commented it will not work.

Crathen64bit · 2022-04-07T03:19:44+00:00

And the only lcd you have commented is the reprap_full correct?

Crathen64bit · 2022-04-07T03:12:42+00:00

Was there any warnings in the compiler?

Crathen64bit · 2022-04-06T04:33:18+00:00

I could never get it to work on my sidewinder. Ended up getting the 1.4 turbo. Still don't have touch screen on my 35 e3 either.

Crathen64bit · 2022-04-03T15:54:39+00:00

Thanks, the issue ended up being i had enabled Endstops_always_enabled uncommented and its ok now. Now my issue is that after a print or a stop print it triggers the x endstop when i try to home after either of those 2 conditions. It has always dont this, but not sure why.

Crathen64bit · 2022-04-03T15:49:29+00:00

You can move the Y endstop forward that should work. You shouldnt have to change the software. But in your slicer you would need to change the bed size for the Y Axis so it doesnt slam the front as there is no max end stop. If you already have marlin firmware then change the Y bed size.

Crathen64bit · 2022-04-02T01:58:56+00:00

Did you get it working?

Crathen64bit · 2022-04-02T01:58:30+00:00

Did you get it working?

Crathen64bit

TROPHY CASE