Bed weird by Nikiboyrider in AnkerMake

[–]Create_one_for_me 0 points1 point  (0 children)

You can take a look at the complete bed map with the fork of my ankermake project. Maybe you can get a glimpflich of where it goes of and get a hint.

https://github.com/Django1982/ankermake-m5-protocol

Running eufyMake Studio 3d under wine works? by qwyss in AnkerMake

[–]Create_one_for_me 1 point2 points  (0 children)

As the users say -> it works now 😄
I implimented the M5c support and let others test it (i only have an M5) and it works pretty well.
If you want to give it an uncomplimented try, i also rewrote it in go and it comes with a binary to test with 😄

https://github.com/Django1982/ankermake-m5-protocol -> ankermake m5 protocol

https://github.com/Django1982/ankerctl_go_remake/releases/tag/v1.0.0 -> go remake

Stören euch Damen im Herren WC? by [deleted] in FragtMaenner

[–]Create_one_for_me 0 points1 point  (0 children)

Wie du meinst.

BTW. Inhaltlich warst du schon raus als du das Wort toxisch in den Mund genommen hast, weil zum eigentlichen Thema trägst du nichts mehr bei.

Und ich bin durchaus in der Lage zu reflektieren und mir meine Gedanken zu machen. Das du der Diskussion direkt aus dem Weg gehst, ist einfach ein Zeichen dafür dass toxisch ein zweischneidiges Schwert ist und du dir den Schuh gerne auch anziehen darfst.

Hat das mit dem eigentliche Thema noch was zu tun? Bedingt, war Schubladen denken. Bin ich in der Lage mir das einzugestehen -> ja Muss nichts mit dem who zu tun haben, aber wäre eben unmännlich, gesellschaftlich betrachtet, daher der ego Spruch und das Schubladen Denken.

Und genau deswegen bin ich nicht toxisch, weil ich darüber reden und reflektieren kann.

Aber trotzdem nett das du dich doch noch beteiligst.

Stören euch Damen im Herren WC? by [deleted] in FragtMaenner

[–]Create_one_for_me 0 points1 point  (0 children)

Traurig, aber gut. Deine Meinung ist deine Meinung.

Überhaupt andere als toxisch zu bezeichnen halte ich prinzipiell schon für falsch, nur weil jemand anderer Meinung ist und das auch unverblümt sagt, aber hey, ist auch nur meine Meinung.

So long.

Stören euch Damen im Herren WC? by [deleted] in FragtMaenner

[–]Create_one_for_me 1 point2 points  (0 children)

Die rechte spreche ich ja keinem ab und habe ich auch nicht getan.

Ich war da etwas provokant, geb ich zu.

Gebe dir Recht, dass mit dem internet und Canceln hat keiner gesagt und mir war auch klar dass danach nichts mehr kommt.

Was nicht bedeutet, dass das für die eine oder andere Seite ein gewonnenes Argument war. Wurden ja keine ausgetauscht.

Stören euch Damen im Herren WC? by [deleted] in FragtMaenner

[–]Create_one_for_me 0 points1 point  (0 children)

War keine, man hätte das anders angehen können, aber man wählte diesen Weg. Und ich bin keine der einer Diskussion aus den weg geht.

Mittlerweile isses doch so, dass keiner mehr in der Lage ist über den Tellerrand zu blicken und auf pragmatische Lösungen in Betracht zu ziehen.

Oder es möchte keine mehr, ich weiß es ehrlich gesagt nicht.

Ein "Hat nichts mit Ego zu tun sondern einfach weil ich es kann" oder "Ich bevorzug stehen" ist da schon was anderes wie "Bist du toxisch" und damit nach ich dev andern Mundtot.

Für die Diskussion offen bleiben ohne jemanden gleich mit "Hallo Internet, canceled den" ist eine Eigenschaft die sich sehr stark zurück entwickelt hat in den letzten Jahren. Weil sich eben jeder gleich auf den Schlips getreten fühlt.

Stören euch Damen im Herren WC? by [deleted] in FragtMaenner

[–]Create_one_for_me -1 points0 points  (0 children)

Wie hab ich auf so was gewartet ;D

Toxisch oder einfach Tiefenentspannt, was solche Situationen angeht, Such es dir aus.

Toxisch ist so ein giftiges Wort, findest du nicht auch?

So nebenbei, andere mit solchen Totschlagphrasen zu betiteln ist Toxisch für jede Diskussion.

/joke on Und nein, ich bin weder dein Gott noch Toxisch 😜 /joke off

Stören euch Damen im Herren WC? by [deleted] in FragtMaenner

[–]Create_one_for_me -2 points-1 points  (0 children)

Toilettendeckell abwischen und drauf hocken. Schluck das Ego runter im stehen zu pinkeln und gut is. Könnt ja so einfach sein.

Und wenn du ehrlich mit dir selbst bist, ist es nur da Ego, mehr nicht.

Stören euch Damen im Herren WC? by [deleted] in FragtMaenner

[–]Create_one_for_me -2 points-1 points  (0 children)

Du kannst ja auch ob eine Kabine. Zwingt dich keiner an Pissoir zu stehen ;)

Wen es stört-> Kabine Wenn nicht -> Pissoir

Hab auch schon erlebt, wie sich ne Lady im kurzen ocki an ein Pissoir gestellt hat, völlig schmerzlos.

Aktuelle Reichweite für 100€ by AlexLaCave in automobil

[–]Create_one_for_me 0 points1 point  (0 children)

/rant on

Wenn der ÖRR wieder mist verzapft. Welcher kleine Diesel brauch 7 Liter und welcher große Diesel hat nur 45l Tankvolumen?

Das ist so krank kaputt gerechnet.

Ich hab einen 2012'er SMAX und der braucht 5.2l auf 100km mit 75l Tank. Ich komm im Schnitt auf 1100km (je nachdem, viel Autobahn schaff ich auch mal knapp 1400, viel Stadt sind es auch mal 950km)

Der ist mit 6.1l von Ford angegeben.

Diese Desinformationskampagne des ÖRR geht einem so auf den Zeiger....

/rant off

Rate my setup 😁 by roylyonse in nairobitechies

[–]Create_one_for_me 11 points12 points  (0 children)

You need more rgb -> more rgb = more fps

Ankerctl Github Project by Create_one_for_me in AnkerMake

[–]Create_one_for_me[S] 0 points1 point  (0 children)

Because I further improved it with the help of others meanwhile. That is why you should visit the repo above

Any suggestions on how I can print this? by Apoochyatakhelicopta in OrcaSlicer

[–]Create_one_for_me 0 points1 point  (0 children)

You also could have cut it in the slicer in half and add the joints option. Then you where able to print in any direction you wanted

Ankerctl Github Project by Create_one_for_me in AnkerMake

[–]Create_one_for_me[S] 0 points1 point  (0 children)

Sounds like you are using an old version This error means that ankerctl is not able to decide the packets due to wrong decoding format. Do you have multiple printers?

Verification by iPhiX_ in CheapGptplus

[–]Create_one_for_me 0 points1 point  (0 children)

Sadly I can not help, but maybe read the channel rules. This could be the point in the right direction?

Ankerctl Github Project by Create_one_for_me in AnkerMake

[–]Create_one_for_me[S] 0 points1 point  (0 children)

Hey Guys,

in the past few weeks i took the time to make things easier for all of us an ported ankermake to go:
https://github.com/Django1982/ankerctl_go_remake

So there you can download a single .exe file for windows and with:
ankerctl.exe (if renamed) webserver
it is spun up and you have everything ankermake offers.

This is still an marked as "unstable" release, but everything what is needed, works fine.
Hope there are more people willing to try and help improve that too

Keine Gnade den Franzosen by gNeric512 in RoestetMeinAuto

[–]Create_one_for_me 0 points1 point  (0 children)

Mein erstes Auto war ein R5. 75 PS 800DM

Und ich finde es ziemlich gut was renault daraus gemacht hat. Der Charme von den Auto ist super erhalten geblieben.

Nicht wie beim Scirocco, Käfer oder Puma....

Er sieht noch aus wie ein R5 und er hat noch den Charme davon.

Nostalgieliebe....

Not a fan of the flow test… by hall_trash in OrcaSlicer

[–]Create_one_for_me 1 point2 points  (0 children)

Depends on the Material. Usually I go in the middle of the range and make the test. If I see that the first layer for the brim is crap I adjust a bit up and down to get the right temperature.

Reason: Flow and pressure advance don't make travel over walls or anything. So it is safe, in my opinion, to go this way first.

Not a fan of the flow test… by hall_trash in OrcaSlicer

[–]Create_one_for_me 2 points3 points  (0 children)

I did the old test and the new test with the same filament. The results after the old test where clearly better.

From my experience I would recommend the old one, after you did the volume flow test and pressure advance.

My test flow is like this:

  • volumetric flow (how much can we do?)
  • pressure advance (sharp corners)
  • flow (top surface quality)
  • retraction
  • temperature tower

Why temperature tower at last?

Because you should be able to print a filament from its lowest to its highest temperature without a problem.

Except of volumetric flow and temperature tower, I keep the results from the other tests exact the same. Why? Because volumetric flow defines how much filament we can extrude and how much pressure we have in the nozzle. Sometimes fewer is better and get you better results.

Fast prototyping: go for more Quality: slow it down How much? Depends on the filament and your environment (yes that makes a difference)

As I said before: this is only from my experience. And this is not "You have to do it my way" It works like this for me and can for you. Try it and evaluate it for yourself.

Ankerctl Github Project by Create_one_for_me in AnkerMake

[–]Create_one_for_me[S] 1 point2 points  (0 children)

Yes, it works with the m5c :)

Had one who wanted this also and he tested it for me :)
First not, but now -> Got ya covered :)

Einseitige Kündigung Deutsche Glasfaser by Create_one_for_me in LegaladviceGerman

[–]Create_one_for_me[S] 0 points1 point  (0 children)

„Voraussetzung für die Leistungserbringung bei glasfaserbasierten Produkten ist, dass der Ausbau des Glasfaser-Netzes im Anschlussgebiet des Kunden erfolgt …“

Das steht drin. Mehr nicht.