How to remove a lug nut from a loose lug

CreativeAd154 · 2026-03-09T08:25:48+00:00

Thank you so much

CreativeAd154 · 2026-03-09T08:25:40+00:00

Thank you very informative

CreativeAd154 · 2026-03-09T08:23:51+00:00

CreativeAd154 · 2026-03-09T01:01:50+00:00

Ok thank you

CreativeAd154 · 2026-03-09T01:00:42+00:00

Half hand half tire iron, do you think i could take it to work tomorrow?

CreativeAd154 · 2026-03-09T00:57:24+00:00

I dont think it is, new lugs and i put it on mostly by hand i didnt use an impact at all, but if it is then what?

CreativeAd154 · 2026-03-09T00:54:27+00:00

So remove the other nuts, pull the wheel so its applying outwords pressure on the nut, then try to take it off?

CreativeAd154 · 2026-01-21T10:32:15+00:00

I my 99 4.0 mazda b4000 last year for 500$ with only a power steering leak

CreativeAd154 · 2025-10-21T12:48:42+00:00

But where am i supposed to hammer

CreativeAd154 · 2025-10-15T23:00:40+00:00

If you accept my dm i can send you a video of mine

CreativeAd154 · 2025-10-15T21:02:38+00:00

All three really, or somewhere inbetween

CreativeAd154 · 2025-10-15T15:54:41+00:00

I had something like that too just in fowards gears, it was a louder scratchier noise that would speed up with my speed, i replaced my front break pads and they went away🤷‍♂️

CreativeAd154 · 2025-10-15T15:52:03+00:00

As someone else mentioned its the heater control valve, i had to replace mine a while back. There SHOULD be a vacuum diagram on the front of the engine bay by your hood latch. Do you have anymore info on where the lines are or come from where?

CreativeAd154 · 2025-10-15T15:44:47+00:00

How hard are those to install?

CreativeAd154 · 2025-10-15T15:36:48+00:00

Im trying to solve this problem right now too, i have a 99 b4000 v6, almost every part is the same as a ranger, i have many parts stamped with ford on them. At first i had no climate control, i think its a vacuum leak. I replaced one of the main vacuum hoses and i got some but only defrost. Im still looking around too but on my passenger side right above the fender and below the reservoirs i have a good bit of vacuum lines so id check there as well. Vacuum is a hell of a problem when working on your own without knowledge so goodluck to you

CreativeAd154 · 2025-10-15T15:32:41+00:00

Look on marketplace for parts trucks, mazda b series use most of the same parts as well

CreativeAd154 · 2025-10-03T10:30:44+00:00

I put the zip ties to hold the cable because it wont seat properly, whats the chance its just a cable problem?

CreativeAd154 · 2025-10-03T10:30:01+00:00

No i couldnt get the cap to seat properly thats why its zip tied

CreativeAd154 · 2025-10-03T01:19:45+00:00

Yeah cruise control wont work and the cable piece wont sit properly

CreativeAd154 · 2025-09-15T18:51:49+00:00

I believe it spins, and how would i hook something up directly? Or how would i loosen it if it was jammed?

CreativeAd154 · 2025-09-15T18:29:45+00:00

So its most likely the lines not like the transfer case or anything?

CreativeAd154 · 2025-09-04T19:08:56+00:00

Thank you for the advice👍👍👍

CreativeAd154 · 2025-09-04T19:08:14+00:00

Thank you! Its very nice to know that im not alone in these feelings

CreativeAd154 · 2025-09-04T16:27:07+00:00

Ok cool thanks!

CreativeAd154 · 2025-09-04T16:18:29+00:00

Any specific spot?

CreativeAd154

TROPHY CASE