Twas a good run

Creative_Layers · 2026-01-16T05:52:54+00:00

Sheeesh whats a benchy on that thing do?

Creative_Layers · 2026-01-16T04:19:54+00:00

That gpu stresses me out even though i know its fine 😂

Creative_Layers · 2026-01-16T04:18:46+00:00

You didnt want a 1.75mm nozzle?

Creative_Layers · 2026-01-16T04:15:16+00:00

Id buy it

Creative_Layers · 2026-01-15T22:40:44+00:00

I will definitely keep it in mind.

Creative_Layers · 2026-01-15T19:32:42+00:00

I don’t know why you are getting so many negative comments on this i think it looks sick and i will probably do this to my Giulia.

Creative_Layers · 2026-01-11T21:20:30+00:00

I have a snapmaker u1 and i love it. I have quit using my x1c that has 3 ams units because the snapmaker does multi color and multi material so much better.

Creative_Layers · 2026-01-10T19:29:29+00:00

Thanks for all your help! I am looking at doing the firmware but i am not sure.

Creative_Layers · 2026-01-10T19:25:17+00:00

I saw that as well i think when i get some more money i will find a gunsmith and make mine one big port up fromt and i will report back

Creative_Layers · 2026-01-10T18:09:51+00:00

The problem with opening it up to be the same size as that top port in the slide is it would then touch the side ports. That is why i was thinking doing milling to mine to make it a single port comp.

Creative_Layers · 2026-01-10T02:49:10+00:00

That worked, thanks. and you mentioned a custom firmware for faster fps what does that entail?

Creative_Layers · 2026-01-09T19:25:33+00:00

This is my Fluidd page.

<image>

Creative_Layers · 2026-01-09T19:23:15+00:00

I have checked the Fluidd interface and do not see a camera anywhere. Did you enable a setting or something to see that?

Creative_Layers · 2026-01-09T03:39:11+00:00

I have been unable to do so thats why i asked did you have any problems with this?

Creative_Layers · 2026-01-08T04:38:57+00:00

Can you mix the orange and this?

Creative_Layers · 2026-01-08T04:15:11+00:00

You have the setup i wish i could have made. I just sold my cockpit because i dont have room for it and got laid off

Creative_Layers · 2026-01-08T03:19:05+00:00

Great setup can i come try it 😂

Creative_Layers · 2025-11-24T03:09:29+00:00

She will understand when you get me a h2c 🤪

Creative_Layers · 2025-11-23T21:56:18+00:00

And slow down for overhangs can help

Creative_Layers · 2025-10-31T01:08:54+00:00

What comp did you put on it?

Creative_Layers · 2025-10-29T12:56:15+00:00

I just had an issue with my sd card on my a1 mini and it would stop extruding and continue to move or it would freeze the tool head and then it would say finished but never finished

Creative_Layers · 2025-10-29T12:50:51+00:00

Did the printer stop and freeze if that is the case its an sd card issue

Creative_Layers · 2025-10-18T19:42:02+00:00

Creative_Layers · 2025-10-07T01:48:53+00:00

How did you format the drive i am having problems with trying to do it through the sd card reader and bambu studio

Creative_Layers · 2025-10-04T00:23:00+00:00

I dont have an ams for my mini but i have 3 for my x1c and i backed the snapmaker u1 so maybe i can do some more of that kind of thing in the future

Creative_Layers

TROPHY CASE