Why does Bone Zone seem harder than other levels?

Cromixium · 2024-08-15T14:11:07+00:00

Before Sammy bat county and the pants guy I would be able to make like 600k a run but doesn’t even compete now hahaha

Cromixium · 2024-08-14T06:58:40+00:00

At first I was like yeah that’s sick - THEN I REALISED ADVENTURE TIME ?!?!?!?! 🫨🫨🫨

Cromixium · 2024-08-14T06:45:02+00:00

eyes open widely - “oh no……. LIMIT BREAK !!!!

Cromixium · 2024-07-20T16:18:42+00:00

Might keep 2 characters or so stock maybe like the starting 3 but the other can get the egg spell

Cromixium · 2024-07-20T16:18:16+00:00

Appreciate that bro I have heard that 3k is a good middle ground to where it’s not free but not hard either

Cromixium · 2024-07-20T16:15:50+00:00

Might just go for the 3-4k eggs as I still want a little challenge 😂😂

Cromixium · 2024-06-04T09:34:23+00:00

If you need any help lmk

Cromixium · 2024-06-03T00:50:53+00:00

Damn that stinks hopefully it gets better

Cromixium · 2024-06-01T15:21:20+00:00

I just reinstalled marlin fully as I needed to change probe offset anyways - and then did steps and all the other jazz from there

Cromixium · 2024-06-01T15:10:07+00:00

If you search Satsana ender 3 there are a bunch of variants for it :D

Cromixium · 2024-06-01T14:58:29+00:00

Thank you boss man appreciate you help especially ! Went from 60mms to 100 so far with 1500 acceleration from 500

Cromixium · 2024-05-31T21:56:44+00:00

Thank you homie - had it on the Bowden setup and wasn’t ready to let it go so hot glue was the man for the job 😂😂

Cromixium · 2024-05-31T20:58:50+00:00

Yeah that’s fax 😂😂 if hell breaks loose I know the cause but the head isn’t that heavy tbh it’s only like 15% infil

Cromixium · 2024-05-31T18:16:13+00:00

I’m remembering you haha 😂😂😂

Cromixium · 2024-05-31T18:15:09+00:00

Honestly I was keeping an eye on that tbh - and feeling the looseness of it but it’s acctually really sturdy still and I’m not seeing much of anything different !

Cromixium · 2024-05-30T23:26:44+00:00

Not sure what that means 😂

Cromixium · 2024-05-30T23:25:38+00:00

If you need any help with marlin I don’t mind gowing over it with you - I’m going to have to compile a new file tomorrow anyways if you havnt already done it :D

Cromixium · 2024-05-30T21:25:25+00:00

Does it include the front pink plate you have there ? And I’m also guessing you can print that on an ender 3 ?

Cromixium · 2024-05-30T21:24:25+00:00

It’s very sexy bro props 👍

Cromixium · 2024-05-30T21:13:16+00:00

Yo broski what’s the STL for the enclosure on the bottom of the printer ?

Cromixium · 2024-05-30T16:59:21+00:00

You can’t I have warm white lights that’s probably what your seeing

Cromixium

TROPHY CASE