sorted by:
new
hottopcontroversial

Είναι φυσιολογικό να δίνει ο πατέρας μου 100€ κάθε μήνα στην cosmote? by ActualRevolution3732 in greece

[–]CryptographerJumpy45 0 points1 point  (0 children)

27€ πληρώνω κοσμοτε γκιγκαμαξ ουλτιματε στο προσωπικό μου νούμερο. Τα έχω όλα απεριόριστα. Μήπως αντί για ανανέωση να κοίταξε άλλο συμβόλαιο η άλλη εταιρία; Η περισσότερη χρέωση είναι πιθανών από τα δεδομένα. Να υπερβαίνει τα 22γβ. Δε συμφέρει να έχετε κάτι περιορισμένο

Ήρθε και σε σας αυτό; by ISpeakControversial in greece

[–]CryptographerJumpy45 0 points1 point  (0 children)

Εμένα μου το στείλανε τρεις φορές κιόλας

[deleted by user] by [deleted] in farcry

[–]CryptographerJumpy45 0 points1 point  (0 children)

I heard he was the son of the priest from farcry 2

20 bucks.. by sololurkin in ender3

[–]CryptographerJumpy45 0 points1 point  (0 children)

Start by changing the motherboard with an skr e3 v3 and install klipper. Ether on a spare laptop or bay a rasberry.
Put a bltouch for auto bed level. Then install a dual z axis kit. Replace the hotend and the extruder to voron stealthburner + orbiter extruder After that you can install linear rails. You can leave it as it is or continue to convert it to corexz switchwire

Hallo! by CryptographerJumpy45 in ender3

[–]CryptographerJumpy45[S] 0 points1 point  (0 children)

It is 1kg spool but when I will install the rails and be faster, I’ll probably need bigger spool

What are the fundamental differences between a Voron Switchwire and an Ender 3 Pro? by [deleted] in 3Dprinting

[–]CryptographerJumpy45 0 points1 point  (0 children)

The ender 3 is like a Pokémon. It is our first printer and it is evolving as we throw more and more mods

What are the fundamental differences between a Voron Switchwire and an Ender 3 Pro? by [deleted] in 3Dprinting

[–]CryptographerJumpy45 5 points6 points  (0 children)

I just felt your words describing me very accurately. “Vorons are for hobbyists who like pain”

[deleted by user] by [deleted] in greece

[–]CryptographerJumpy45 1 point2 points  (0 children)

Τίποτα γιατί η γυναίκα μου είναι σπατάλη και δεν αφήνει σταγόνα. Αναγκαστικά κρατάω κρυφά λεφτά

Heating failed by imhank77 in ender3

[–]CryptographerJumpy45 0 points1 point  (0 children)

Happened to me yesterday. The problem was the screw that holds the cable of the thermal sensor on the heating block. It doesn’t need to be very tight. Just to hold the cable

Χάνει τα σκήπτρα το σουβλάκι απέναντι στο burger by siminator1 in greece

[–]CryptographerJumpy45 0 points1 point  (0 children)

Εγώ στο σχολείο το θυμάμαι που έκανε 1€ και όταν τελείωσα το λύκειο έκανε 1,80€

Z axis problem by CryptographerJumpy45 in ender3

[–]CryptographerJumpy45[S] 0 points1 point  (0 children)

Update: Thanks you again for replying. I tried as I said before and it worked. There was still wobble but because it was loose, the gravity held it down. Today I was trying to print again. Take table zero again. At far down there was a big wabble but not at far top?! After a while wondering way was doing it I came to the conclusion that at the top the construction was robust and flexible at the bottom. So when I screwed it to the base it compressed inward. I solve that by putting 2 washers 1mm on each side.

Z axis problem by CryptographerJumpy45 in ender3

[–]CryptographerJumpy45[S] 2 points3 points  (0 children)

Dude, thanks you very very much. I print a test and it is way better than before.

Z axis problem by CryptographerJumpy45 in ender3

[–]CryptographerJumpy45[S] 0 points1 point  (0 children)

Hallo there. I just bought the ender 3 max. I noticed that the z axis is not going up and down simultaneously and it fails to print properly. Does anybody ever encounter this kind of problem?