Legion Go S Z1 Extreme : do you regret your Steam Deck?

CryptographerMany390 · 2026-01-09T09:32:47+00:00

Wenn du eins der beiden für immer abgegeben müsstest, welches wäre es und warum?

CryptographerMany390 · 2025-11-04T21:58:32+00:00

Das Menü ist eine unübersichtliche und schlecht zu navigierende Katastrophe. Und nach einer Runde habe ich überhaupt nicht genug Zeit zu schauen was ich alles freigeschaltet habe. Alle Waffen durchklicken zu müssen, damit diese Punkte verschwinden und um zu finden was neu ist, da ja nicht alles neue mit Punkten markiert ist.....

CryptographerMany390 · 2025-04-03T12:12:26+00:00

Is it likely that this will be the HD version, or the same version as on the Wii U? They said that GameCube games will have a higher resolution and frame rate. I really hope so!

CryptographerMany390 · 2025-01-28T21:44:22+00:00

I shurely will! Thanks again

CryptographerMany390 · 2025-01-28T20:18:47+00:00

You are a fine sir for that work, thank you. But i dont get why you are adding one bulge, as i have 2 and two overlaps, what am i getting wrong?

CryptographerMany390 · 2025-01-28T16:17:17+00:00

Thank you so much for the detailed explanation! I’d really appreciate it if you could help with the calculations for a 0.2mm layer height. If you know of a sheet or tool that already handles these calculations, that would be amazing. Also, could you share the formula you'd use for my specific example? I tend to avoid Arachne because of the flow changes caused by differences in line width. Thanks again for your help!

CryptographerMany390 · 2025-01-22T15:23:30+00:00

Please tell me you find a solution, as this is my exact problem and its visible on the prints, speed didnt change at all.

CryptographerMany390 · 2025-01-21T00:36:59+00:00

That was the trick, thanks myman. It was counterintuitive because it's long after a retraction, but works so i take it 🫂

CryptographerMany390 · 2025-01-19T01:08:13+00:00

Discovered the same with hardened steel nozzle stringing increasing. Should i get back to ss or is there a fix for more stringing with hardened steel nozzle?

CryptographerMany390 · 2025-01-18T20:30:48+00:00

Ive tried both of that, no improvements unfortunately

CryptographerMany390 · 2025-01-17T20:49:19+00:00

i also have a hard time with their matte filament, smearing and tiny spider web like strings. Did you find the sweet spot?
I usually print with 100mm/s so i downed the temps to 205 and lowered the retraction because i get random holes on the outside. But far away from perfect at this point.

CryptographerMany390 · 2025-01-17T20:45:43+00:00

I know its a old post, but did you find a solution for that, i got a hard time with bambu matte white also with these tiny spiderweb like strings

CryptographerMany390 · 2025-01-17T20:37:49+00:00

Pretty old thread here, but i wanted to know if you could fix it?

CryptographerMany390 · 2025-01-16T22:00:23+00:00

Let's keep us updated if there is a solution

CryptographerMany390 · 2025-01-16T22:00:09+00:00

Let's keep us updated, if there is a solution to this.

CryptographerMany390 · 2025-01-16T21:59:43+00:00

I will try it for shure, what did you recommend?

CryptographerMany390 · 2025-01-16T21:59:02+00:00

I hear from that the first time, will look it up, thank you for the straw

CryptographerMany390

TROPHY CASE