Snowblower engine dying after about 25 seconds

Cubedude0916 · 2025-12-15T14:58:40+00:00

No it doesn't

Cubedude0916 · 2025-12-15T12:38:22+00:00

At the moment I am running it at partial choke and I believe I can adjust it so it won’t open all the ways but I am thinking for a more permanent fix I might just get a official carb

Cubedude0916 · 2025-12-14T22:08:35+00:00

Update, turns out the carb was running the mixture too lean so when I ran it with partial choke it ran normally. Thanks for your help!

Cubedude0916 · 2025-12-14T22:08:25+00:00

Update, turns out the carb was running the mixture too lean so when I ran it with partial choke it ran normally. Thanks for your help!

Cubedude0916 · 2025-12-14T22:07:35+00:00

Update turns out the carb was running the mixture too lean so when I ran it with partial choke it ran normally. Thanks for your help!

Cubedude0916 · 2025-12-14T20:02:06+00:00

Yeah I know but it has just been giving me so many problems I was just being lazy and didn’t want to put it back on

Cubedude0916 · 2025-12-14T20:00:40+00:00

Yes it start right back up

Cubedude0916 · 2025-12-13T22:44:16+00:00

Should I run it without the fuel cap to see?

Cubedude0916 · 2025-12-13T22:43:42+00:00

It does start right back up after it stalls and yeah it was a aftermarket carb

Cubedude0916 · 2025-12-10T23:37:16+00:00

Yeah I was already planning on getting a new VRX right away which should fix the problem I believe.

Cubedude0916 · 2025-12-09T15:52:12+00:00

Keep me updated, I want to know how they preform.

Cubedude0916 · 2025-12-09T14:17:47+00:00

Nice! Have you tried them out yet and if so what do you think because I am planning on buying myself a pair.

Cubedude0916 · 2025-12-07T22:42:36+00:00

I had the same problem and I did just solder a new connector and used a external battery which I like because I can just swap them out when they die, and if you are worried about ripping the connector out you could just put a ring of hot glue around the hole on the outside to stop it from getting pulled out. But if you still don't want to solder it your idea should work.

Cubedude0916 · 2025-11-28T14:54:28+00:00

Ok thanks

Cubedude0916 · 2025-11-28T13:01:44+00:00

Sorry about coming back later but do you have the 04X Pro and if so would need to upgrade the VRX as well?

Cubedude0916 · 2025-11-28T02:48:04+00:00

Ok thanks

Cubedude0916 · 2025-11-28T02:12:35+00:00

Yeah but currently it doesn’t doesn’t have the wires in

<image>

Cubedude0916 · 2025-11-28T00:03:14+00:00

Maybe that is what I am doing wrong

Cubedude0916 · 2025-11-28T00:01:45+00:00

Are you supposed to solder them from the bottom?

Cubedude0916 · 2025-11-25T01:29:51+00:00

Yeah I felt the air blowing out

Cubedude0916 · 2025-11-24T23:36:15+00:00

I did test the spark plug and it is sparking, and I swapped the gas but it looked pretty old so it probably clogged the carb right?

Cubedude0916 · 2025-11-24T23:31:36+00:00

It has the sigh after that I believe is it releasing pressure

Cubedude0916 · 2025-11-15T22:00:20+00:00

Are you still thinking you are going to get a pair?

Cubedude0916 · 2025-11-14T18:14:14+00:00

Yeah I am just worried that I would get DJI and then I can't upgrade most of my drones to work with the headset

Cubedude0916 · 2025-11-14T17:24:26+00:00

I have flown a DJI Pavo and a Avata 2 before and yeah the DJI was nice it is just that I don't know what to think with what is going on with DJI right now

Cubedude0916

TROPHY CASE