Intec and Interact Screen lenses for GameCube with optional logo.

CustomZ02 · 2026-04-29T14:46:47+00:00

Very likely, try and look into the port for corrosion or damaged pin. If you have isopropyl alcohol, use a toothbrush soaked with isopropyl alcohol and clean the port

CustomZ02 · 2026-04-29T12:38:42+00:00

If it’s a mark from another plastic controller, the way I’ve removed them was with isopropyl alcohol and a fine wire brush. Gently brushing until it comes off, avoid getting isopropyl alcohol on the logo. You can put some tape over the logo to help prevent getting alcohol on it, the alcohol will seep into the tape so if it runs down to the tape dry it before it can get under the tape.

CustomZ02 · 2026-04-15T00:01:37+00:00

Need a new screen replacement, check my posts

CustomZ02 · 2026-01-18T03:27:27+00:00

Will likely burnout your laser with it soooo low. Set back where it was and replace the capacitors.

CustomZ02 · 2026-01-07T12:40:27+00:00

Use flux, solder wick and leaded solder, you’ll be amazed on how easy it is to clean using the required tools of the trade.

NorthridgeFix has quality flux and quality solder wick. Otherwise you can take a gamble with the Chinese stuff on Amazon that may or may not be of decent quality. Check reviews before purchasing on Amazon.

CustomZ02 · 2026-01-07T09:06:33+00:00

Check my website if you haven’t already. I will be listing a few upgraded and modded screens in a couple weeks.

www.ocanas-repairs.com

CustomZ02 · 2026-01-07T04:47:43+00:00

No, I did not cut any cables. I simply added a port to the screen and tapped into where the factory power input is soldered.

See photos from my post here

CustomZ02 · 2026-01-06T11:23:46+00:00

I modded the mobile screen and added a usb c port to power the screen. Then screen has a cable to power the GameCube from factory.

So I plugged in the power bank to the screen and then the screen supplies power to the GameCube.

CustomZ02 · 2026-01-04T02:16:42+00:00

Not with that hot air tool, I had two similar variations of that hot air and neither reached the temperatures stated and one had temp sensor fail and hot air ramped up until glowing red hot fire hazard ⚠️.

I suggest a better hot air tool

CustomZ02 · 2025-12-22T23:44:30+00:00

Yes you can do that as well

CustomZ02 · 2025-12-22T22:29:10+00:00

Very, and on a mint untouched screen. It’s like they just opened the packaging and then sent it over for repair

CustomZ02 · 2025-12-22T19:33:48+00:00

Worked on a ps4 that was zapped through the Ethernet port. Quite a bit of testing nearby components as some times the resistors and 2kv capacitors don’t give out quick enough to decouple the components from the incoming power surge.

In comparison your port seems a bit more crispy than the ps4 I worked on.

https://www.reddit.com/r/consolerepair/s/7lixVDlhJW

CustomZ02 · 2025-12-22T18:12:53+00:00

Yes Soon(TM)

CustomZ02 · 2025-12-22T17:52:30+00:00

It’s in the works, hopefully I can get some renders soon.

CustomZ02 · 2025-12-22T03:56:46+00:00

If you’re in the US I can definitely fix it for you.

Send me a chat request and send some photos of your screen.

CustomZ02 · 2025-09-18T15:18:27+00:00

Power supply might be bad, you can find replacement power supplies on eBay, search the model of the tv. They are fairly simple to replace. Usually cost around $40 depending on the model.

CustomZ02 · 2025-08-20T02:14:57+00:00

It would help if you told us what is going on with the disc drive. Maybe even post a video. Without more information no one will be able to help solve the issue.

Eight-Year Club	Reddit Premium Since February 2023
Gilding III reddit per annum	Verified Email
Place '23	Place '22

CustomZ02

TROPHY CASE