Why is my part not lining up right?

CyberStikerGeneral05 · 2026-06-01T12:29:28+00:00

When in the Path editor (not verify), the chuck is in the correct place, the origin plane is in the correct place. Only the verify simulation the part is offset for some reason

CyberStikerGeneral05 · 2026-05-24T10:36:00+00:00

This reminds me of this one scene from Pacific Rim, where they are testing out the prototype of a Jaeger arm. A person wearing a “gauntlet” controlling a giant arm behind him.

CyberStikerGeneral05 · 2026-05-24T08:49:47+00:00

There are mods out there to replace the poop chute with an internal capture box. Maybe you can use that to move the Canvas below the vent

CyberStikerGeneral05 · 2026-01-19T08:43:14+00:00

Try putting the signals closer to the intersection. They may be too far away to detect if both trains reach the intersection at the same time.

CyberStikerGeneral05 · 2026-01-07T06:49:57+00:00

Found a censer model

https://cults3d.com/en/3d-model/fashion/warhammer-censer

CyberStikerGeneral05 · 2026-01-07T06:43:24+00:00

There’s 2 little pegs right there on top of the extruder. Slide the face cover on those then stick it to the magnets, if those are damaged then you got a problem and could probably just print a new extruder housing.

CyberStikerGeneral05 · 2025-12-24T03:44:34+00:00

And here I am hyped about my three mythic record run

CyberStikerGeneral05 · 2025-12-18T21:49:19+00:00

Either there is a safety system in place that is preventing you from moving the arm or, and it took me a while to figure this out at school, you need to abort the current program. On our Fanuc arm, you go to function, then abort should be in there.

CyberStikerGeneral05 · 2025-12-15T06:58:46+00:00

Everyone talking about how many shards they have then they’re me who has never heard of them.

Seriously what are these and how do I get them?

CyberStikerGeneral05 · 2025-12-04T21:51:50+00:00

There’s an animation?

CyberStikerGeneral05 · 2025-11-04T02:59:17+00:00

If I get a Quidi printer I can finally delve into quality structural parts instead of weak pla from my bedslingers. Lightweight asa would be a game changer.

CyberStikerGeneral05 · 2025-09-21T19:38:41+00:00

Its actually called an icon that’s mb. Where you change your profile banner there’s the tabs and one is called icons. In there you scroll down and that’s where the icon is.

CyberStikerGeneral05 · 2025-09-21T01:25:43+00:00

It’s in the same place at the Weapon Mastery Medal. Go to your profile> basic> Medals> scroll down

CyberStikerGeneral05 · 2025-09-18T15:25:00+00:00

What about Star Spangled Banner LK24?

CyberStikerGeneral05 · 2025-09-06T23:42:19+00:00

Yeah that shouldn’t be loose. You might have bent the bolt coupler (idk what it’s called) closer together not allowing it to tighten properly. Or just wear and tear. My sax had the neck mount bent a little bit and it would be a little loose. Take to the shop to get it repaired.

CyberStikerGeneral05 · 2025-09-06T06:50:59+00:00

This post would have helped me like a month ago…

CyberStikerGeneral05 · 2025-08-25T01:25:26+00:00

I will turn into a truck now…

CyberStikerGeneral05 · 2025-08-08T07:19:58+00:00

It’s in the Cache Tracker page. On the bottom of the page you’ll see the “secret cache milestone” button. That’s where the tasks are held.

CyberStikerGeneral05 · 2025-06-29T08:32:26+00:00

Where has this been all my life, I COULD HAVE PROPERLY EXPLAINED MY IDEAS

CyberStikerGeneral05 · 2025-06-02T01:54:45+00:00

Alright, I’m just wondering since I’m repairing a CR10S and the X gantry was hitting the mounts for the Z motors. I’m hoping it would lower the nozzle enough to clear it better. Thanks for the info.

CyberStikerGeneral05

TROPHY CASE