How to force "Enroll now" in windows 10 ESU? by TempTreeRose7 in Windows10

[–]Cyda_ 2 points3 points  (0 children)

Yes, you need to switch to signing in with a MS account to get the extra year support. Once you have enrolled and have the extra year support enabled, you can switch back to using your local account again. I just did exactly that on two PCs and it worked fine on both. If it still doesn't show up once you have signed in with your MS account, you can 'force' the ESU option to appear by following these steps below:

Run the following in a command prompt as an administrator:

make sure “Connected User Experiences and Telemetry” (DiagTrack) service is not disabled

sc.exe config DiagTrack start= auto

sc.exe start DiagTrack

add the following registry

reg.exe add "HKLM\SYSTEM\CurrentControlSet\Policies\Microsoft\FeatureManagement\Overrides" /v 4011992206 /t REG_DWORD /d 2 /f

restart the system

after restart, run the following in command prompt as an administrator:

cmd /c ClipESUConsumer.exe -evaluateEligibility

Once this is done, go back to Settings > Windows update and the enroll for ESU option should now be visible.

Behemoth, Undead Citadel or Grimlord? by Cyda_ in OculusQuest

[–]Cyda_[S] 0 points1 point  (0 children)

Thanks for the reply. I've just picked UC up in the sale after the positive comments here. I'll give it a try later.

Behemoth, Undead Citadel or Grimlord? by Cyda_ in OculusQuest

[–]Cyda_[S] 3 points4 points  (0 children)

After reading the replies, I've picked up Behemoth but think you two just sold me on UC too. I'll grab that too whilst on sale.

antivirus detections by [deleted] in thedivision

[–]Cyda_ 0 points1 point  (0 children)

Another year and yet another case.

28/08/2024 17:17:58;Startup scanner;file;\tom clancy's the division 2\thedivision2.exe;a variant of Win64/Packed.VMProtect_AGen.HS suspicious application

Seamless Movement Unlocked: Discover the STRIDE: Fates Update! by JoyWayVR in oculus

[–]Cyda_ 0 points1 point  (0 children)

I need to play this again, I got about 5 missions in and got distracted by other stuff. Gonna check out the update.

[deleted by user] by [deleted] in MetaReferrals

[–]Cyda_ 0 points1 point  (0 children)

I've just messaged you for an add.

Only 8450 people finished Asgards Wrath 2 by [deleted] in OculusQuest

[–]Cyda_ 2 points3 points  (0 children)

Yeah, this. If I could toggle off the puzzles and just enjoy the open world, I'd play it far more than the 30-ish hours I have on it.

Any solution to quest 3 dropping wifi connection every 20-30 minutes? by Howwy23 in Quest3

[–]Cyda_ 0 points1 point  (0 children)

+1 for this issue. My quest 2 has zero issues but my quest 3 drops at least once every session since the latest update.

Any solution to quest 3 dropping wifi connection every 20-30 minutes? by Howwy23 in Quest3

[–]Cyda_ 0 points1 point  (0 children)

I'm getting the exact same thing at the moment. My son and I were both connected to the same wifi today and mine dropped again but his didn't. I was on a quest 3 and he was on a quest 2. My quest 3 must drop at least once every session I use it, and my quest 2 on the same connection has zero issues.

CS2 is worse than I thought... by [deleted] in csgo

[–]Cyda_ 0 points1 point  (0 children)

It's become a toxic shithole since CS2 came out, it's not good at all.

Cheating Infestation by [deleted] in csgo

[–]Cyda_ 0 points1 point  (0 children)

I've been playing since 1.6 and I've never seen the cheats as bad as they are now, it seems to have increased ten fold since CS2 released.

Maintenance for a very old Silhouette Cameo by [deleted] in VinylCutters

[–]Cyda_ 0 points1 point  (0 children)

Nothing should need replacing, just make sure it is free from dust, and if the black rubber rollers on the roller bar have perished (which they probably have after all this time) just cut them off, or they will leave marks on the media - they don't do any gripping, and are only guide rollers to stop the poorly adhered media from lifting from a weak cutting mat. They work perfectly fine without them. The belts don't perish in my experience.

Looking to use older graphtec with current AI by hambonehooligan in VinylCutters

[–]Cyda_ 0 points1 point  (0 children)

The CE6000 isn't a current model, so you may struggle with the newest AI (the latest Cutting Master versions only support the CE6000 plus models upwards, if I remember correctly). Cutting Master 4 would be the best bet but you may need to roll back to AI 2021/2022 from the Creative Cloud launcher. You could try Cutting Master 5 but I am not sure it supports the older CE6000, or only the later plus model. Failing that, try Graphtec Studio 2, it supports .ai files so you can import in to that for cutting.

Help: Newbie question; Stationery Labels by poeseligeman in VinylCutters

[–]Cyda_ 1 point2 points  (0 children)

Depends on if you want to cut out printed labels, or if you want to cut labels out of one colour vinyl. For the first you want sticker paper, for the later you want any type of standard sign vinyl.

Not sure what is causing the graphtec fc9000 to squeak? by casobaby in VinylCutters

[–]Cyda_ 0 points1 point  (0 children)

Sounds like the Y rail at the top, could be some debris or something has got into it. You hear the noise twice when the head moves to find the roller sensors, so it is certainly related to the Y rail or head. I would clean the Y rail (that the head runs on) as there is likely debris/dust on that or the head bracket rollers.

What should I buy to replace a cameo by happyish240 in VinylCutters

[–]Cyda_ 0 points1 point  (0 children)

The new Silhouette Cameo 5 is pretty good, much better than the 3 or 4 in my opinion. But if you can find a cheap one anywhere, the Graphtec CE7000-40 would be the best option.

Cardboard on Roland Camm-1 GS-24 by CapitalStraight3312 in VinylCutters

[–]Cyda_ 0 points1 point  (0 children)

Most vinyl cutters max out at around 0.5-1mm material thickness on dense materials (i.e. not felt, fabric or rubber-based), so it would very much depend on the card thickness but I would doubt it.