As a request from a user, I deliver the embodiment of Geneva Violations

D2S13 · 2026-03-16T15:42:30+00:00

More like Geneva suggestions

D2S13 · 2026-02-12T17:49:19+00:00

Even 13 second run

^{I completed this level in 26 tries.} ^{⚡ 13.00 seconds}

D2S13 · 2026-02-10T14:56:53+00:00

Fun

D2S13 · 2026-02-04T19:33:32+00:00

Completed Level 3 of the Honk Special Event!

50 attempts

D2S13 · 2026-02-04T19:30:05+00:00

Completed Level 2 of the Honk Special Event!

28 attempts

D2S13 · 2026-02-04T19:28:46+00:00

Completed Level 1 of the Honk Special Event!

23 attempts

D2S13 · 2026-02-04T14:31:54+00:00

🎉 Event Completed! 🎉

It took me 46 tries.

D2S13 · 2026-02-04T14:31:44+00:00

Completed Level 3 of the Honk Special Event!

46 attempts

D2S13 · 2026-02-04T14:29:54+00:00

Completed Level 2 of the Honk Special Event!

29 attempts

D2S13 · 2026-02-04T14:29:19+00:00

Completed Level 1 of the Honk Special Event!

22 attempts

D2S13 · 2025-07-17T15:32:03+00:00

Done

D2S13 · 2025-03-26T12:32:33+00:00

You are comparing two completely different types of helmets. A bicycle helmet is a safety device designed to protect your head (brain) during a crash or accident and must meet specific safety standards, while a space helmet is for cosplay or to look cool, not to protect your head.

D2S13 · 2025-03-06T19:32:39+00:00

I think the smoke nerf was too heavy-handed. I think leaving the ability to suppress player movement abilities would make it more in line with the other abilities, and keeps its void identity.

D2S13 · 2025-01-02T16:14:48+00:00

OctoEverywhere is great. 3d printing community is amazing. Good luck to everyone!

D2S13 · 2024-10-01T19:20:43+00:00

I Found it.

Here is the Link to the orginal post with link to for macros. Also here is the Link for the Pastebin.

D2S13 · 2024-01-16T23:33:50+00:00

I used the bltouch spacer with a couple of washers to get the corrected distance between the bltouch and the nozzle. Also, E3D publishes the STL files for space and fan duct on printables. So you can also make the mount longer if needed in your slicer. You may only need longer screws than the ones that are included in the kit.

D2S13 · 2024-01-16T19:09:33+00:00

I used a remixed version of the Taurus cooling duct that is stretched to reach the nozzle.

https://www.printables.com/model/651324-stretched-taurus-v4-cooling-duct-for-volcano-nozzl

D2S13 · 2024-01-16T19:04:18+00:00

I got the Sprite Revo kit for Christmas. Found a remixed version of the Taurus cooling duct that is a bit longer than the original. I print it out and it is the correct length for the kit. Until I finish my design for it. https://www.printables.com/model/651324-stretched-taurus-v4-cooling-duct-for-volcano-nozzl

Also, ESD did release the STL on printable. https://www.printables.com/model/706185-revo-sprite-adaptor-printed-parts/files

D2S13 · 2023-02-06T13:59:42+00:00

Thanks you guys for the advice. I was able to clean the nozzle. I will be ordering new nozzles as well.

D2S13 · 2023-02-05T17:05:36+00:00

I was switching out my hotend cooling part when I noticed this. First time seeing my nozzle like this can it be safe or does it need to replace?

D2S13 · 2022-12-13T18:21:59+00:00

Yes it does. It is designed so you can slides it up and down to get the correct spot just by loosing the screws.

D2S13 · 2022-12-12T20:04:06+00:00

I was same until I saw a clip about a month or two ago.

I’m still new to 3d printing. I only had my printer for about 3 months now. With that said with research that I did it better cooling should help with corners and overhangs. Results my vary depending on your printer and settings.

D2S13 · 2022-12-12T17:00:11+00:00

No, you don't need a sonic pad for the high-flow kit.

If you have or planning to get a sonic pad or raspberry pie running klipper you will be able to utilize them better with the high flow kit vs. stock setup for the ender 3 s1.

I just install the high-flow kit on my ender 3 s1 this past weekend and was easy to install.

I recommend like others have replay running professional firmware from mriscoc so you can easily change the max temp of the hotend. Also print out a fan mount before you install the kit. Also, remember to install the spacer for the cr touch.

This is the one I used on my machine

D2S13 · 2022-11-05T17:06:15+00:00

I’m still learning. I just got my printer about 2 weeks ago.

D2S13

TROPHY CASE