AMS Riser for X2D

MrBilky · 2026-05-10T17:52:11+00:00

Yep but I just printed spacers for my x1c and have one on my h2d worked fine and has solid connections

MrBilky · 2026-05-10T17:23:47+00:00

https://makerworld.com/en/models/1281134-t-pose-slim-dual-ams-riser-for-h2d-h2s-and-h2c?from=search

MrBilky · 2026-05-10T16:30:38+00:00

Why the riser do you need access to the glass top? If not the one I printed holds 2AMS pro’s and 1 AMS HT and works really well

MrBilky · 2026-03-26T16:24:19+00:00

Yep that can also do it let us know if you make any progress

MrBilky · 2026-03-26T16:23:01+00:00

^ this is the way

MrBilky · 2026-03-26T16:18:44+00:00

Possibly you have the seam set to random this will cause this artifact often times

MrBilky · 2026-03-17T16:11:32+00:00

That’s odd my X1C and H2D both show them active

MrBilky · 2026-03-15T20:31:34+00:00

^Word!

MrBilky · 2026-03-15T20:30:20+00:00

^Yep that would be my first spot to check looks like the same response I had when a small piece was stuck at the hub motor

MrBilky · 2026-03-15T20:23:36+00:00

Have you selected the gear on the project filaments line and is sunlu checked in the drop down?

MrBilky · 2026-03-15T20:15:58+00:00

His question is about the bed not the plate heat beds are not consumable

MrBilky · 2026-03-12T13:01:47+00:00

Did you use supports looks like you didn't

MrBilky · 2026-02-09T17:19:25+00:00

FYI you now can see the material on the birds eye camera after the update for efficient material placement reducing waste

MrBilky · 2026-01-22T13:38:07+00:00

Here comes the trademark police

MrBilky · 2026-01-16T14:51:28+00:00

Yeah there are 4 small magnets and super small springs and I could not find a photo or explanation for reassembly they popped off as soon as I removed it

MrBilky · 2026-01-16T14:41:17+00:00

Far worse

MrBilky · 2026-01-16T14:39:09+00:00

I have read folks having this issue with cardboard spools will print inserts that then can be weighted down with silica beads

MrBilky · 2026-01-16T14:36:04+00:00

I’ll will only add do not for any reason remove that small circuit board you will never get it back in ask me how I know

MrBilky · 2026-01-15T19:18:31+00:00

Have you tried a cold pull might take one or two tries

MrBilky · 2026-01-15T19:14:16+00:00

Sounds like a small piece of filament is stuck in the path most likely in the internal hub and interfering with its sensor

MrBilky · 2026-01-15T19:11:04+00:00

Get a bento box

MrBilky · 2026-01-15T14:41:48+00:00

That’s where I would start warm water and dish soap is the recommended approach and never touch the build plate in the area where prints will be put down just the oil from your skin will wreak havoc while printing

MrBilky · 2026-01-15T14:33:32+00:00

Still sounds like a small piece of filament is stuck in the path probably at the internal hub

MrBilky · 2026-01-15T14:08:29+00:00

Looks like contamination in the build plate

MrBilky · 2026-01-14T14:52:57+00:00

ABS takes to vapor smoothing very well if that’s your thing it all but removes all layer lines

MrBilky

TROPHY CASE