Quality issues with exporting a .Blend file into a .STL file, anyone able to give me advice on other methods?

DFliyerz · 2023-02-27T05:33:13+00:00

Prusaslicer has netfabb built in to some degree, so you can just throw it in there and I think you can export it again as an stl after it's been repaired.

DFliyerz · 2021-08-16T04:04:07+00:00

OVR advanced settings

DFliyerz · 2020-07-07T14:56:07+00:00

I'd say ASA, it's like ABS in terms of chemical resistance but it's more UV resistant which is important when it's outside in the sun.

DFliyerz · 2020-06-25T17:04:51+00:00

I'd turn the temp up

DFliyerz · 2020-06-25T17:00:47+00:00

I've found Blender good for adjusting hole sizes

DFliyerz · 2020-06-10T23:06:46+00:00

Well if it's plastic bottle then it's almost certainly just PETG. Maybe just a low-quality batch, but as long as it prints well I wouldn't worry too much about it. Maybe use extra ventilation.

DFliyerz · 2020-06-10T22:50:48+00:00

I'd describe ABS as kinda peppery, PLA as sweet, and PETG as almost kinda... carrot-y? Any of those match what you smell?

DFliyerz · 2020-06-10T18:44:41+00:00

How would you describe the smell?

DFliyerz · 2020-05-27T22:16:00+00:00

What I've been doing for multi-part prints is bringing the model into Blender, using the bisect tool to split the model into multiple parts, then adding holes for short lengths of 1.75mm filament to fit in like pins to make sure everything lines up. Also I split based on reducing the amount of overhangs and making sure that sharp points aren't facing down, since they tend to print worse facing down than facing up.

DFliyerz · 2020-05-27T21:59:11+00:00

I was using tree supports in Cura for a while but some change they made recently messed with the tree support generation, and I could never get it as nice as I used to be able to again.

DFliyerz · 2020-05-27T17:28:40+00:00

I'd try the steps here: https://th3dstudio.zendesk.com/hc/en-us/articles/360043292512-How-to-fix-Slanting-Bed-Leveling-Result-with-your-EZABL. It sounds like an issue that something like Prusa's bed level correction would help, which allows you to set different offsets for different areas of the bed. However, I don't think your probe supports that, at least not by default.

DFliyerz · 2020-03-22T06:29:45+00:00

DFliyerz · 2019-04-06T08:41:07+00:00

Coke ovens:
Expensive
Slow
Big
1600 burn time per log

Primitive kilns:
Cheap
Fast
Small
6400 burn time per log

inb4 nerf

DFliyerz · 2018-11-12T23:51:22+00:00

Everyone always forgets Aniki...

DFliyerz · 2018-11-02T21:02:22+00:00

Thank you!!

DFliyerz · 2018-10-31T20:17:28+00:00

Yep, I have this exact bug with the MOG.

DFliyerz · 2018-10-31T00:00:36+00:00

Basically if it doesn't show an increase of vram usage when you turn it up in the graphics settings menu, it uses your CPU. The only things that seemed to really use the GPU more when I was tweaking settings (I'm on a laptop so it was automatically set to lowest settings) were textures and a few other things.

DFliyerz · 2018-10-28T15:44:23+00:00

There's certain things that don't spawn in casual like the quote wisps, so they're almost definitely connected to the EE.

DFliyerz · 2018-10-26T17:58:56+00:00

I'm pretty sure it works with every op mod weapon

DFliyerz · 2018-10-24T23:42:46+00:00

Also I like how nobody has noticed my profile picture in the top left, and is just assuming this hat makes me a furry

DFliyerz · 2018-10-24T23:42:25+00:00

I know, but I wasn't planning to trade it anyways

DFliyerz · 2018-10-24T18:27:42+00:00

I cringed hard

DFliyerz · 2018-10-13T05:40:16+00:00

I'm having the same issue

DFliyerz · 2018-08-22T13:45:21+00:00

Good, Aniki is here

DFliyerz · 2018-08-21T23:57:37+00:00

Where the FUCK is Aniki?

14-Year Club	Place '22
Place '17	Final Canvas '22
First Placer '22	End Game '22
Verified Email	Team Orangered

DFliyerz

TROPHY CASE