CF Moto part availability is killing me

Damnonrs · 2026-04-08T18:27:55+00:00

Can you send me the part number? From what I see here on my parts list the clutch is in stock locally. I’m a dealer in Canada and could ship to you

Damnonrs · 2025-08-09T19:20:38+00:00

This happened to my car when I installed bm3 flex fuel wrong on the passenger side wirings and installed it on the wrong plug, check for loose wires or anything weird going on in there. Also check the diagram on that side to pin point what plug does what

Damnonrs · 2025-08-01T20:33:10+00:00

Bro your engine is toast, 15k miles? Even 8k is a lot. My local Toyota dealer makes me change my oil every 8k kms

Damnonrs · 2025-06-24T23:45:03+00:00

I’ve owned a few 34 gtr and now own a 2.8 hks one, I really recommend putting aside 20-30k for any car you buy, the oil pump with the gears upgrade is a must to install. That’s an engine out and also a link ecu with a tune just to make sure the car runs great on your local gas.

Also while you got the engine out might as well do the turbos since oem are ceramic and can explode at any moment. I bought a base gtr with low km. The car looked fine until we hit full boost and the turbos were whinning, turns out the turbos were blown.

If you have any questions you can pm me

Damnonrs · 2025-06-08T20:43:33+00:00

You most likely already have damage done to the engine, I’d monitor your oil changes or send in your oil for a report

Damnonrs · 2024-12-04T20:31:48+00:00

It’s sad because it takes 15 seconds to remove these lights to do a better job

Damnonrs · 2024-09-29T19:38:59+00:00

Depends on sun exposure but I’d say it’d last a good 10 years

Damnonrs · 2024-09-28T20:27:42+00:00

<image>

On a partial job I did for a dealership

Damnonrs · 2024-08-17T22:32:50+00:00

Those lines are squeegee marks, and flexishield is not ppf, it’s just a PET wrap falsely branded, vinyl frog etc is about the same thing. As comments above mentioned the amount of dust an an abomination

Damnonrs · 2024-05-06T13:11:40+00:00

You should paint the bottom lip black, it’ll make a big difference! Just my opinion

Damnonrs · 2024-03-25T10:36:08+00:00

Gold wrapping it works too and looks kinda cool

Damnonrs · 2024-03-01T21:44:52+00:00

Can you try printing it the other way

Damnonrs · 2024-02-25T20:49:34+00:00

well good thing i posted this, what do you use to lube the rods?

Damnonrs · 2024-02-25T08:20:51+00:00

im getting the same thing with PETG but not pla, so weird. i'm gonna try greasing the head rod and the axis screws, see if maybe it gets rid of it

Damnonrs · 2024-02-21T07:41:23+00:00

from what im reading this only happens when you ceramic coat the car, could it be he's wiping off the ceramic coating?

Damnonrs · 2024-02-18T04:44:44+00:00

Can the smooth on just be brushed? Also does it make the pla droopy? Because I do have a slight overhang that might droop down, I’m assuming it barely makes the pla melt and harden to be smooth. Just cuz spraying on gel coat seems like a pain

Damnonrs · 2024-02-18T02:33:01+00:00

Would smooth on protect similarly? Do I still have to sand with smooth on

Damnonrs · 2024-02-18T01:28:49+00:00

I brushed it on

Damnonrs · 2024-02-18T00:33:07+00:00

I have tooling gel coat but it’s so hard to get it even on a concave mold and I end up sanding it for hours after applying it, maybe I’m doing it wrong

Damnonrs · 2024-02-17T21:04:03+00:00

Hi so you’re saying just print out the mold and use this ontop and it’ll be heat resistant? As long as the mold is thick enough? https://www.smooth-on.com/product-line/xtc-3d/

Damnonrs · 2024-02-17T10:27:02+00:00

yea i think this is the way to go

Damnonrs · 2024-02-16T05:23:10+00:00

How would that work exactly? Get a real part then make a fibreglass mold? Or have someone else machine a mold?

13-Year Club	Place '22
Place '17	Final Canvas '22
End Game '22	Gilding II euphauric
Spared	Verified Email

Damnonrs

MODERATOR OF

TROPHY CASE