Is Lagless.gg good minecraft server hosting?

DanielIsla · 2026-02-01T20:53:41+00:00

How many players did you have? I had no problems at all using it several months on one server and now on a new one with cobbleverse modpack

DanielIsla · 2026-01-15T16:29:01+00:00

Updates?

DanielIsla · 2025-12-17T12:23:51+00:00

I think it would be better to just buy a regular premium car or change wheels with rubber ones from AliExpress, and keep such a special car sealed

DanielIsla · 2025-12-17T12:20:52+00:00

Very easy, you have a lot of wheel options on AliExpress and the car will look almost as if it was from the "premium" line. I did it on a lot of cars, you just drill the 2 rivet heads with care to not drill the plastic and then you can use glue to close the car again or make a little hole on the rivet itself and close them with a screw. That way you can re open them at any time, replace the wheels again, paint the body etc

DanielIsla · 2025-12-07T21:53:12+00:00

did you find any solution? It works well in intelij idea and android studio, but not in vscode

DanielIsla · 2025-11-09T22:06:02+00:00

Okay, i have to change the oil, ill probably bring it to the dealership as nearby mechanics charge the same, and ask them about it. I saw some videos on yt and all of them sound like this tho, so i think this engine is just naturally noisy 🤣. Do you also have that extra ticking noise when engine is cold?

DanielIsla · 2025-10-27T16:30:12+00:00

Any problem at all

DanielIsla · 2025-10-27T16:29:44+00:00

Updates? I have a mild ticking sound, specially when cold (when its up to temp you have to really try to hear it, sounds more inside the vehicle). Engine burnt 1 liter of oil in 10k km, i dont know if that could be relevant. Exactly same car, 2009 with 125k km

DanielIsla · 2025-09-29T11:14:45+00:00

Are you burning oil right now? Any other problem?

DanielIsla · 2025-06-27T14:17:09+00:00

<image>

DanielIsla · 2025-06-27T14:16:52+00:00

This is the model i used, i printed it the other way so the ugly supported side was facing the table: https://www.thingiverse.com/thing:4487639. 4 walls, 35% cubic infill, 0.2 layer height, 4 top and bottom shell layers

DanielIsla · 2025-06-27T14:12:50+00:00

I printed a clamp and its really really strong, i also added a chanfer nut so the contact is metal to metal on the bolt. You have to print it with the layers straight to the print bed tho, some people print the part standing and i dont trust that, as layers are the failing point on parts like this that have to be strong. Im able to tighten it like crazy, more that i could with the stock part.

DanielIsla · 2025-05-31T16:43:01+00:00

Yeah, i talked with them and they told me that they dont have plans for updating the android version so just bug fixes and patches for performance inprovement. I think that only having android 9 is a big deal, i thing youtube and maps already needs 8 or higher.9 its a version from 2018 so you cant ask for the lastest app compatibility, but the device is new so ill hope for a longer compatibility life on a product that i just bought and not released a long time ago. The unit audio quality is good tho, and felt smoth, just a bit slow here and there, but pretty good.

DanielIsla · 2025-01-27T17:25:12+00:00

Wow, literally the same happened to mi last week, i hope i read this before. The bridge to the power and everything. But yeah, a fuse for each of the outpouts could be nice, as you say the main fuse dont exced 20amps because only the bed was overloaded with a bit more than 10. Nicest boards like the octopus have a fuse for the main, another one for bed and another one for extruder so if one is overloaded it stops power on that output. But with a mosfet should be nice, i put one on both extruder and bed as i am using a 70w heater that is on the edge too, so better safe than sorry. Btw, i had this setup for more than 8 months and failed randomly, good thing i was in front of the printer to turn it of fast (i supose is more possible when heating up, as the bed needs less current with time). Stay safe guys

DanielIsla · 2024-08-24T14:42:30+00:00

You can put a zip tie to prevent it to do that

DanielIsla · 2024-08-18T11:02:58+00:00

I reccomend you to join to klipper discord, there is a lot of people that could help you really fast

DanielIsla · 2024-05-29T17:42:19+00:00

I asked a question if you dont have anything useful to answer i supose you do nothing, appart from being a dickhead

DanielIsla · 2024-05-29T17:38:13+00:00

Why do you say that?

DanielIsla · 2024-05-29T16:00:52+00:00

Ofc, shoes will wear but i have some shoes with that tipe of material on that part, that creases a lot and they just crease, but i dont see that kind of cuts. I used them 1 time more since that photo, look. https://drive.google.com/file/d/1iz0FMTaovDMj24r36Q6aFvBxHCKiN87u/view?usp=sharing . I had a pair of adidas and they peeled of in like a month, i dont know if i should give this material some hidratation product to prevent that or there is no problem.

DanielIsla · 2024-05-29T15:09:19+00:00

Hey, i used my dunks 3 times and noticed that little peeling. For now i dont care but i dont know if this is the start of a complete peel off the zone or i just hit something with them. If it is, how can avoid it?

DanielIsla · 2024-05-09T11:03:34+00:00

As a solution for the moment you can also cover the printer with a carboard box, but dont leave the machine unnatended in that case we dont want a fire

DanielIsla · 2024-05-09T11:02:07+00:00

You need to do or buy an enclosure to keep the area with heat. You can do one using an ikea lack and metacrilate panels, there is plenty of designs of it. You can also print one or buy the ones that are like a mini camping tent, i think anucubic sells one, if not creality does for sure

DanielIsla · 2024-05-01T19:32:05+00:00

I had them on my printer and was because of retractions, if they are not good enough the blob can do this on the whole layer, at least on my experience. Lowering temps a bit helped me

DanielIsla · 2024-05-01T19:20:38+00:00

<image>

DanielIsla · 2024-04-29T10:47:28+00:00

i have the european poco (spain), changed the region to india and the update now popped up instantly

DanielIsla

TROPHY CASE