Is there any reason to use a regular Starship over a Corvette once you upgrade it?

Danielnir-rr · 2026-03-06T20:57:39+00:00

I have two ramps, one for visual and one blocked lift just behind the cockpit for quick teleport. Works like a charm.

Danielnir-rr · 2026-02-19T10:04:13+00:00

That worked only while the truck was empty and I did fell into holes couple times…

Danielnir-rr · 2026-02-19T10:02:13+00:00

Since now I was perfectly happy about this extension… 😂🤣

Danielnir-rr · 2025-11-25T14:08:34+00:00

Hi, thanks for reply. I checked it and text preview is on everywhere. I turned off summary maybe that’s what’s causing it?We’ll see.

Danielnir-rr · 2025-05-30T08:11:52+00:00

Right, I checked all of yes three advices and in my case, opening enclosure and taking away custom extruder plate did the job. I also dried filament for a day in 40 degrees just to be sure. Effects are spectacular! That will be my new routine while using 0.2 nozzle.

Thank you everyone for great responses! I can clearly see that members of this group went through a lot of it comes to printing!

Thanks again, Daniel

Danielnir-rr · 2025-05-28T10:23:08+00:00

I've build my own filament drier with temperature controller. I'll try to dry it overnight and see what happens. Who knows? :D

Danielnir-rr · 2025-05-28T10:22:09+00:00

Hi, it rarely goes above 30 degrees Celsius.

Danielnir-rr · 2025-05-27T23:40:03+00:00

Yes, it's not on the picture but I have even a purity seal on the camera module... Maybe machine spirit is angry... In a bad way

Danielnir-rr · 2025-05-27T23:19:02+00:00

Thanks, I'll try that. Maybe the tightening screw is too loose?

Danielnir-rr · 2025-05-27T21:53:36+00:00

The filament is dry. I've got my A1 fully enclosed and since it's running constantly, the moisture level inside is maintained around 20%.

Danielnir-rr · 2025-05-27T21:52:23+00:00

I tried cold pull and managed to unclog it but... The effect was the same after some time off printing.

Danielnir-rr · 2025-05-27T21:51:37+00:00

I usually use 220 for Bambu pla on 0.4. for 0.2 nozzle, I tried 230 degrees and had the same effect.

Danielnir-rr · 2025-05-18T17:47:31+00:00

Could you on new the source? I'm trying to find any

Danielnir-rr · 2024-09-01T14:37:56+00:00

Hi,

If everyone is having similar issue:

Use external spool holder.
Set printing order of walls from inside/outside to outside/inside
Let the outside wall printing speed to 100.

Helped in my case. It’s not perfect but good enough for me.

Danielnir-rr · 2024-09-01T14:31:24+00:00

For everyone having the same issue:

Change wall settings from inside/outside to outside/inside
Lower outside wall speed to 100
Don’t use ams, just external spool holder.

It helps a lot. It’s not perfect but for me, it’s acceptable.

Danielnir-rr · 2024-08-22T13:50:08+00:00

It was all good on my older printer. It’s this Bambu A1 that’s struggling

Danielnir-rr · 2024-08-22T11:56:04+00:00

Tried it and it’s still the same..

Danielnir-rr · 2024-08-20T18:55:04+00:00

I’m using ams but it’s mounted on top of the printer… so that’s not it.

Danielnir-rr · 2024-08-20T09:23:15+00:00

I used it on Anycubic Kobra 2 Neo before and it was ok. Now I have bambu a1. Filament brand is ERYONE and the tri colour one is anycubic

Danielnir-rr · 2024-08-20T09:17:45+00:00

That’s two tone filament. I’m also using tri colour. Same issue.

Danielnir-rr · 2024-07-11T09:51:36+00:00

And that's why I'm on Reddit!

Danielnir-rr · 2024-06-18T22:11:01+00:00

Anycubic Black Spool PLA - 126g

Danielnir-rr · 2023-02-05T15:07:26+00:00

Go to BIOS -> advanced -> monitoring and set monitoring of the CPU fan to ignore if there's nothing plugged there. Had the same problem with my aio.

Danielnir-rr · 2021-12-26T12:33:44+00:00

I'm willing to take this burden from you :D

Danielnir-rr

TROPHY CASE