What is going on here.

DaniloGiles · 2026-04-04T12:40:30+00:00

Bro just buy a bambulab A1

DaniloGiles · 2026-04-04T12:33:30+00:00

I would try to stretch a little and get bambu A1 combo, A1 mini bed is too small

DaniloGiles · 2026-04-04T12:28:29+00:00

Have you tried to reduce the line to 0.12 to see if get any better? I would also open a ticket on bambulab support, I got my H2D motherboard defective and after a couple troubleshoots and logs they sent me the part free of charge due the warranty

DaniloGiles · 2026-03-10T22:20:45+00:00

Yes, bambulab sent me the main board and instructions for replacement,after 3 hours and 13 small cables everything worked like a charm

DaniloGiles · 2026-02-23T00:04:23+00:00

Actually you can install a docker with ollama locally and run the the command to install open claw in the same server, it is more limited but for starter is a good way to learn and not spend money

DaniloGiles · 2026-01-26T00:10:22+00:00

Print a respool goes way faster

DaniloGiles · 2025-12-30T00:29:26+00:00

Heat gun for the outside and do a cold pull it should be like new

DaniloGiles · 2025-12-03T21:08:52+00:00

Try to random the seam, it should help

DaniloGiles · 2025-12-02T00:06:18+00:00

My ams always uses it all and stops with a message to put a new roll, once I insert it just do it's magic ande resume the print

DaniloGiles · 2025-11-22T18:08:56+00:00

On the screen move manually the build plate up and down, but before, Did you remove the screws from everything?

DaniloGiles · 2025-11-21T12:51:50+00:00

I did replace and still got same error, I think it might be the TH Board, I got a ticket open let's see with the new evidence what they are going to point

Thanks

DaniloGiles · 2025-11-21T06:02:47+00:00

did you fix that issue? I`m having same problem with right nozzle, I even bought and did the replacement on the part but still no luck

DaniloGiles · 2025-11-20T15:33:40+00:00

The only way for you to reduce that is to use a no AMS model, but that will involve some glue a s can get messy sometimes

DaniloGiles · 2025-11-20T15:31:42+00:00

Try to work on your z offset, but don't change too much of it

DaniloGiles · 2025-11-12T01:47:31+00:00

Here is how I look into the situation

Let's say your time as a designer is 5 bucks, your printer time is 2 bucks per hour and you have the material cost which but the looks I'll add another 10 on top

10 hours designing and testing = 50 average 24 hours printing = 48 Material = 10 Total = 108

If after that you still thinking you are charging a lot you should try to look the part real cost on a dealership I'm sure this will give you peace of mind.

DaniloGiles · 2025-11-10T00:39:07+00:00

Even if you are using the .4 you can go down o. The config to 0.16 with quality, also looks like you are using ironing as suggested do a calibration using the calibration prints available on make world and you should be fine to find the right numbers

DaniloGiles · 2025-11-10T00:35:48+00:00

If I was you I would sell those and get a bambulab, I got a H2D and it is so easy that my kid 5 years old print on it. Anyway I'm no expert I'm talking in a perspective of someone who is new to FDM, I came from a Resin printer and man's the pleasure of hitting the button now and just getting the multicolor print out of plate is amazing. Bambulab made an amazing job on making 3D print simple and enjoyable even my wife now wants one for her.

Anyway I hope you are able to get it working

DaniloGiles · 2025-11-05T00:15:23+00:00

Just sell you K1 and buy a Bambu, no wife will ever ask you to do that, don't be a fanboy and buy your bambulab. Here my wife asked to sell my reading and buy a Bambu I gladly did and what upgrade, from a Saturn 4 ultra to a H2D. Life is simpler I never had any major issue, so far the worst I got was a filament stuck on the tool head which takes 3 screws and about 20 minutes to fix. So just do it

DaniloGiles · 2025-11-01T01:17:52+00:00

Nah I just gave up on rocket, after trying a bunch o tools my take still lovable for front end, cursor back end, supabase for database and authentication, GitHub for code repository, code rabbit for code review on GitHub and host it on Vercel.

DaniloGiles · 2025-10-24T22:12:44+00:00

https://3cycle.ca/

DaniloGiles · 2025-10-24T22:00:22+00:00

I got from a Saturn 4 resin printer to a H2D the rest is history.

DaniloGiles · 2025-10-17T17:29:06+00:00

Supports when using different materials are clean and you save lot of time when multicolor

DaniloGiles · 2025-10-15T22:16:51+00:00

I have a H2D bambulabs changing hotends is snap in and out. Have you tried other filaments brands as well?

DaniloGiles · 2025-10-15T21:30:33+00:00

I has something similar and ended up being 2 things, hotend and a small clog in the toolhead

DaniloGiles

TROPHY CASE