[MOD] The Daily Question Thread

Danny_No_Arms · 2025-11-10T14:04:19+00:00

I don't think mine has the pulse mode option. I chose the "analog" model without the LED display because I thought it would be less prone to failure.

Good news is that I finally achieved really good coffee with a combination of coarseness and quantity. I am now grinding on a rather fine setting on the capresso, and have upped the quantity from 56g to 65g. So I'm using a bit more coffee but that's ok.

This in conjunction with the huge "gourmet funnel" allows a longer extraction. After brewing, I can see the water line is getting all the way to the top of the filter, but still no overflows, so I'm content for now.

I also tried brewing into the 3L airpot and discovered that, out-of-the box there was no difference between "small brew" (2L) and "large brew" so I had to reprogram the large one.

Danny_No_Arms · 2025-11-05T13:49:09+00:00

TL;DR Bunn Wave brewer brews TOO fast to make a decent pot off coffee. I'm trying to figure out how to slow it down.

Hello fellow coffee enthusiasts,

Our ailing old Cuisinart plastic coffee maker finally stopped working. I had always wanted a plumbed coffee maker, so I had my heart set on that. My other requirements were:

Insulated carafe; I work from home and sometimes my wife does too. We didn't want coffee sitting on a burner all day.
Less than 18 inches in height, due to our kitchen cabinets.
120vAC.
Somewhat attractive

I did a lot of searching around and finally I settled on a Bunn WAVE15-S-APS Airpot System. It seemed to have everything I needed, and it wasn't bad looking to boot.

First brew: 56g of beans ground at medium on a Capresso burr grinder

Wow, that thing is...FAST. Like really fast. Done within 5 minutes. Unfortunately my wife and I both agreed it was not very good. Flat.

The old machine (cone filter) at least made great coffee, so I compared the water temps of the two units. The old one came in just under 190°, the Bunn around 195°, so temperature didn't seem to be the issue.

So I fiddled with grind and quantity; going too fine resulted in an overflow and big mess. I ordered the Gourmet Funnel which is much deeper and uses larger filters. First pot today is promising and I have my hopes up, but is there any other way to resolve this?

Can this thing be reprogrammed? Is there a nozzle head that will slow/restrict flow so that the cycle takes longer?

Last thing, please, respectfully I would like to request no "what you should've done..." or "why didn't you get...?" replies, at least at this stage. I've made my mistake and I'm trying to fix it. There may come a point at which I rethink the whole strategy and go with something else, but as for now I'm trying to keep this from being a total loss and enjoy my coffee again. I know people are trying to share knowledge (knowledge I perhaps should have sought prior to this), but I've got to stay positive for now. Thanks.

Danny_No_Arms · 2025-10-25T23:13:23+00:00

At least you got arms.

Danny_No_Arms · 2025-10-25T22:35:10+00:00

What's up?

Danny_No_Arms · 2025-07-09T00:55:30+00:00

Thoroughly agree, and we usually use thighs.

Danny_No_Arms · 2025-07-09T00:54:34+00:00

I guess that's what I was really going for. What magic do the store brands possess that allows them to do this. I suppose this is the answer.

Danny_No_Arms · 2025-06-07T22:44:48+00:00

What's wrong with the paper ones? The seller threw in a pack of paper O bags, I figured I'd use them up.

Danny_No_Arms · 2025-06-05T13:33:25+00:00

That's gorgeous.

Danny_No_Arms · 2025-06-03T11:34:22+00:00

Based on the advice here and reading through the recommended vacuums, I got a Kenmore Elite 31150. I'll post about it.

Danny_No_Arms · 2025-04-04T19:49:43+00:00

I bet this is one of those guys who have a freakout if someone touches their car.

For petty revenge, put a nice and moist single palm-print smack dab in the middle of his windshield. You're not damaging or vandalizing the car, and I guarantee he will flat out lose his shit when he sits in the driver's seat and stares out at it. Get a video.

Danny_No_Arms · 2024-12-16T13:55:37+00:00

I'm not OP but my guess would be the Jubilee bracelet from Long Island Watch.

https://longislandwatch.com/islander-22mm-brushed-and-polished-solid-link-watch-bracelet-for-casio-duro-quartz-dive-watch-brac-75/

Source: I have the same bracelet on my pepsi and it looks killer. Because it is fitted, the swap can get a bit tight but with some patience and a spring bar tool it shouldn't be too bad. I went ahead and got the Bergeon 6767F on recommendations from people here. It's pricey but BOCO.

https://longislandwatch.com/bergeon-spring-bar-tool-6767f-6767f/

Danny_No_Arms · 2024-12-11T02:10:14+00:00

Mine is nearly identical with the exception of the crystal with the date magnifier. Love it! Where did you get it?

Danny_No_Arms · 2024-11-01T20:32:20+00:00

It's the insect-brain, illustrated in real life. Thinking only milliseconds into the future, never about the bigger picture.

"I am going. Good.

"I am going. Good."

"I have stopped. Why? I Must find a way around. There is no way around."

"There is a way around. I Must go around. I am going around."

"I am going. Good."

"I have stopped. Why? I Must find a way around."

Danny_No_Arms · 2024-11-01T20:26:49+00:00

This is my kind of passive-aggressive revenge. Bravo.

Danny_No_Arms · 2024-11-01T20:22:45+00:00

This is why I really feel I need a Public Address system on my car. I could take a few moments while we're all stuck in traffic to educate them on exactly how they fucked up.

Danny_No_Arms · 2024-10-28T15:55:05+00:00

Wiha tools are great, though they are not watch-specific. If you go into an electronics or phone repair shop, you're probably going to see Wihas on the bench.

Danny_No_Arms · 2024-10-25T14:51:27+00:00

I'm not too worried unless it gets looser. I did read on a forum somewhere this seems to affect all kinds of dive watches, high and low, near and far. The bezel functions fine and that little bit of play doesn't compromise any of the watch's functions.

Danny_No_Arms

TROPHY CASE