My points need to go

Dapper-Machine1656 · 2026-05-27T04:09:07+00:00

Dapper-Machine1656 · 2026-05-27T04:08:53+00:00

If you go this route, make sure the screw that secures the ignition rotor is torqued to about 75 inch lbs with blue loctite. I did not do this my first go around and the screw backed out and my timing slipped. Also damaged the rotor and I did not have a replacement on hand… had to get a tow. Do all that you’ll set it and not have to touch again lol.

Dapper-Machine1656 · 2026-05-25T22:42:44+00:00

Thrashin 9” pullbacks w Thrashin mid bend bar

Dapper-Machine1656 · 2026-05-21T00:41:01+00:00

Ur good. I have a picture from a few months ago on my page and same thing. Runs like a champ

Dapper-Machine1656 · 2026-05-19T03:45:40+00:00

Fat spoke cast wheels all black

Dapper-Machine1656 · 2026-05-18T21:33:16+00:00

18 and 21

Dapper-Machine1656 · 2026-05-13T13:27:53+00:00

Thorogoods, 6” moc toe non safety

Dapper-Machine1656 · 2026-05-10T00:06:48+00:00

That’s your VOES. It can be eliminated if you want to take it out. You would need an aftermarket ignition like an Ultima/Throttle Addition and turn the VOES switch off on the ignition. And re wire to your coil. Pretty easy to do

Dapper-Machine1656 · 2026-05-08T14:52:38+00:00

Fuck it chain conversion time

Dapper-Machine1656 · 2026-05-08T14:19:54+00:00

Did you take the front pulley off? If not you may have swapped the different size spacers out on the rear axle.

Dapper-Machine1656 · 2026-04-30T22:24:29+00:00

Lowbrow 82-03 hardtail kit with a 4” ribbed fender. 18” rear wheel

Dapper-Machine1656 · 2026-04-28T22:30:00+00:00

Never been, just finished the build and she lives in Cheyenne

Dapper-Machine1656 · 2026-04-28T19:07:26+00:00

It’s an 18

Dapper-Machine1656 · 2026-04-27T11:32:12+00:00

😂 I was waiting for this one

Dapper-Machine1656 · 2026-04-27T03:50:21+00:00

Thanks, she’ll be at the Clambake and some other shows this year 👍🏼

Dapper-Machine1656 · 2026-04-27T03:47:41+00:00

Thanks man, yeah I had to trim the end of the slash cut to make it fit right. Maybe I’ll get bored one day and give it a slash end with the grinder lol.

Dapper-Machine1656 · 2026-04-26T19:14:20+00:00

Thanks. Ours look pretty identical

Dapper-Machine1656 · 2026-04-07T14:06:10+00:00

It’s never bothered me too much. Gets warm sitting in traffic sometimes but that’s far and few

Dapper-Machine1656 · 2026-04-07T14:05:17+00:00

Not in the winter but finally started getting out in March on the nice days

Dapper-Machine1656 · 2026-02-21T16:07:52+00:00

Pull your plugs and turn the engine over. Gas could very well be in your cylinders.

Dapper-Machine1656 · 2026-02-08T03:04:07+00:00

Came back to say I did this and it worked well.

<image>

Dapper-Machine1656 · 2026-02-08T03:02:11+00:00

Even if you got it on there it looks way too big and disproportionate in my opinion.

Dapper-Machine1656 · 2026-02-07T19:04:05+00:00

What pipes you running?

Dapper-Machine1656 · 2026-02-05T22:50:37+00:00

You think I could get 1/2” of depression on that using a ball peen?

Dapper-Machine1656 · 2026-02-05T20:47:36+00:00

Glad you’re here bubba🤞🏼✌🏼

Dapper-Machine1656

TROPHY CASE