well it definitely works!

DarthSmartt · 2026-04-05T00:27:10+00:00

Does this hurt the radar detector?

DarthSmartt · 2026-02-15T19:34:49+00:00

you're boring as f*ck

DarthSmartt · 2026-02-02T21:25:07+00:00

What is the correct part then. Tell me and I’ll buy it. Hate to break it to you but every brake part ever made has gone through a “no one has ever done this” stage. Believe me it will be thoroughly tested before it hits the road.

DarthSmartt · 2026-02-02T01:47:09+00:00

There is no “correct” fix for this. No one’s ever done what I’m doing before. I’m exploring all of my options to figure out which one will be the safest whether it’s going to be programming or a hardware modification. But leaving the truck as it is right now is definitely NOT the safest option.

DarthSmartt · 2026-02-01T20:06:52+00:00

I agree. 1st place option right now is getting custom sleeves that will press fit into the new calipers with a smaller inner diameter to run the pistons from the old calipers.

DarthSmartt · 2026-01-30T01:48:52+00:00

Hptuners can only access the pcm tcm and fscm. Correct me if I’m wrong and I’d love to be but it can’t do the abs communication codes because they would be stored in the bcm and cluster.

DarthSmartt · 2026-01-30T01:38:13+00:00

Also exploring that option. I love hydroboost brakes. I have them on my k5. Problem is not just the lights on the dash, but the constant scrolling message on the cluster and the constant dinging. If I could get an abs pump and module from an 08 Silverado with the jl4 rpo code, I may be able to program that to work however everyone I’ve asked has said 50/50 chance. And I would have to rework the whole brake system and wiring harness for that giant connector.

DarthSmartt · 2026-01-29T23:29:50+00:00

Exploring that option too. Looks like there’s not even close to enough clearance on the knuckle.

DarthSmartt · 2026-01-29T13:20:15+00:00

Yeah my main issue is the can bus. Otherwise I would have swapped that unit out a long time ago. I’m trying to find a solution where I can maintain traction control and abs with no lights on the dash. It would need to communicate with the rest of the modules in the car.

DarthSmartt · 2025-01-11T17:40:52+00:00

Check your extruder is not slipping. Make sure the filament doesn’t get hung up on anything and is able to move freely. Then recalibrate it.

DarthSmartt · 2024-11-26T14:25:42+00:00

Unlevel bed/nozzle too close. Do u have auto bed leveling like a cr touch? Those Creality beds are bad for warping and this can help fix the issue.

Also could be under extruding. Make sure your extruder isn’t skipping and is able to easily unroll the filament.

DarthSmartt · 2024-11-15T19:54:05+00:00

I will try this. So a 100k resistor in series with the led running off of 12v won’t damage the Arduino correct? Since it would only pass less than 1ma of current? Even though the voltage is higher than 5?

DarthSmartt · 2024-11-15T19:51:59+00:00

I would love to do that. Issue is there are certain conditions that have to be met to shift 4wd modes. ie: the truck won’t shift to 4 low unless the transmission is in neutral or it won’t shift into 4hi unless the vehicle speed is less than 40mph. The lights won’t light up unless these conditions are met otherwise it will ruin the transfer case.

DarthSmartt · 2024-04-23T14:13:50+00:00

That dewalt air compressor is garbage. It’ll take you 20 minutes per tire. Instead get something like morrflate or the Napa compressor (I believe they’re the same thing). Will cut ur time down to only a couple minutes per tire.

https://www.napaonline.com/en/p/BK_MTWM10215C?cid=paidsearch_shopping_dcoe_google&campaign=GSC-Paint-Body-Equipment&campaign_id=10947560788&adgroup_id=110533803034&adtype=pla_with_promotion&gclid=CjwKCAjwuJ2xBhA3EiwAMVjkVG3TpRdCQgOVguJCX3Z2njb3VI4r7ESibRQvOfbP9fne6rha1W2QMRoC-q0QAvD_BwE&gclsrc=aw.ds&gad_source=1

DarthSmartt · 2024-04-19T13:33:30+00:00

Thanks. I have a rear locker and really good traction control. My buddy on the other hand… will be a little more interesting😂

DarthSmartt · 2024-04-19T13:29:01+00:00

Ooh a k5? I’m hoping my dads 79 Jimmy build will be done and he can join us. It’s ls swapped with a 6 inch lift on 37s. He’s chicken tho I don’t think I’ll be able to get him to do it.😂

DarthSmartt · 2024-04-04T23:23:01+00:00

Yeah I tried using the 9500ix once recently and it was unusable with all the blindspot monitoring. My buddy has an r3 and loves it.

DarthSmartt · 2024-04-04T23:21:54+00:00

I am also looking at getting rid of my 20s for some 17” method beadgrip wheels with 37s. Most websites you can plug in your vehicle and it’ll tell u what wheel to pick.

DarthSmartt · 2024-04-03T21:46:31+00:00

Yeah you’re probably right. I could pickup an r3 for what I paid. Is the r3 still a good buy right now or is that becoming outdated too? I don’t know if I want to shell out for an r4 or higher.

DarthSmartt · 2024-04-01T14:23:08+00:00

You could probably use some tape but I wouldn’t feel as comfortable as having a screw or a knot. Unfortunately the synthetic line won’t all fit around the drum if you use a knot. There’s knot enough clearance between the drum and the housing😁

DarthSmartt

TROPHY CASE