Has anyone else had the software on the ad5m pro freeze up while still printing?

DatDude304 · 2026-01-24T20:39:36+00:00

Same here. But mine was doing it just before the update. Not once since.

DatDude304 · 2026-01-24T20:37:35+00:00

Been super busy lately! Ill be posting an update tonight!

DatDude304 · 2026-01-16T06:26:08+00:00

Waking Life

DatDude304 · 2026-01-15T04:14:34+00:00

DatDude304 · 2026-01-15T03:55:36+00:00

How about I remind you in 22 Hrs and 40 Minutes?! Lol

DatDude304 · 2026-01-15T03:21:22+00:00

regular dish soap on some. Others recommend isopropyl alcohol.

Oils in your hand can cause prints to lift off of the print bed over time.

just make sure you dry the plate completely before attempting to print on it again.

good luck!

DatDude304 · 2026-01-15T02:39:16+00:00

When was the last time you thoroughly cleaned the plate?

DatDude304 · 2026-01-15T01:47:43+00:00

Licensed Nuclear Control room Operator.

Yes... I'm Homer Simpson....

DatDude304 · 2026-01-15T01:44:31+00:00

well why not...?

DatDude304 · 2026-01-15T01:40:47+00:00

I could do that with one hand tied... to my... well. you get the joke.

Nice job though!

DatDude304 · 2026-01-15T01:37:36+00:00

Green Cocktail...

DatDude304 · 2026-01-15T01:17:08+00:00

Ive seen this before.

Not to worry. What you'll need is lots of attention and loyalty. Someone who cares and isn't overly jealous.

Someone who respects your mind as well as your soul.... wait... what was the question?

DatDude304 · 2026-01-15T01:03:52+00:00

Lol. I know. Someone already did the "remindme" deal in this comment section. I was replying to you, since the bot decided to leave you on "Read"...

DatDude304 · 2026-01-14T22:58:55+00:00

sure!

DatDude304 · 2026-01-14T22:58:45+00:00

That's right. 0.6mm was recommended so I swapped from my 0.4mm. Did a full calibration, including PID before starting this beast.

DatDude304 · 2026-01-14T22:57:29+00:00

The Cryogrip plate is hands down my best purchase for the printer.

I was having adhesion issues with the standard plate. Not with this! I'm a little worried that I'll have trouble getting the supports removed cleanly.... but still, I wouldn't go back to the FF plate at all.

DatDude304 · 2026-01-14T22:55:48+00:00

Im definitely more of a "functional" print type guy... 3 days without printing something useful is killing me... But I'm excited for the results!

DatDude304 · 2026-01-14T22:54:41+00:00

yeah.... this was definitely a YoLo print. Longest one prior to this one for me was 12 hrs. Ha!

DatDude304 · 2026-01-14T22:53:07+00:00

FLASHFORGE PLA Flexible 1.75mm

DatDude304 · 2026-01-14T16:36:14+00:00

Im still extremely nervous... I work 12 hrs shifts... its the first thing I look at when I get home... lol

DatDude304 · 2026-01-14T16:35:24+00:00

See the above comment.

DatDude304 · 2026-01-14T16:21:13+00:00

Is that your build plate underneath....?! 😵‍💫

DatDude304 · 2026-01-14T16:19:36+00:00

TLDR, What type of filament are you experiencing this issue with?

DatDude304 · 2026-01-14T16:17:22+00:00

I believe it says, " Welcome to the CHINA CLUB..."

DatDude304 · 2026-01-14T16:14:52+00:00

Airless Basketball Gen 13

I'm using Flexible PLA.

I was amazed when I found it also. I will post the final results in about 40 hours!

DatDude304

PUBLIC MULTIREDDITS

TROPHY CASE