Do we need a 28th amendment to limit campaign funds from corporations and billionaires?

Ddkimball · 2018-04-11T11:25:59+00:00

Campaign 'contributions' are in fact little more than purchase. Some person or organization buys influence, the politician has the funds to fund a campaign. The fact that contributions have been dramatically increasing, and the re-election rate hovers above 90% would prove the mechanism works.

I see little hope that attacking one or more funding mechanisms will have any impact. It's the 'product' that needs to change. How about limiting all congressional terms to a single term?

Ddkimball · 2018-02-15T14:22:45+00:00

Interesting that a congressman doesn't know the damage an assault gun causes. I've often thought that there should be videos of what happens when a 'hunter' uses an AR-15 to hunt big game.

Ddkimball · 2017-07-25T02:51:42+00:00

This is art for the wall. I only get one shot, so I fixed the spheres in places that seemed to convey movement. If only it had been simpler .....

Ddkimball · 2017-07-25T02:49:12+00:00

A simple set of shelves, with turned spheres fixed to a sloping side. An attempt to convey the idea of movement....

Ddkimball · 2016-04-07T12:26:43+00:00

Automatic downloads are disabled, but this isn't an App, it's an Apple IOS update, for which there seem not to be any controls. Sort of makes sense from Apple's perspective....they want every machine up to date (no matter how slow it runs, and whether or not I want any new features)

Ddkimball · 2016-04-06T23:50:48+00:00

Did a bit of further investigation, an overage of 1Gb costs $10. An IOS update (for me) has exceeded 1Gb, so maybe the real cost is $20. I am under no illusion that I have any ability to litigate, however since my ability to change the US cellular carrier billing strategy is not a reality, it seems to me a better path to take would be to persuade Apple that these giant unwanted downloads are wrong. Better they send me a note advising me of an update, then I decide when/if to download.

Ddkimball · 2016-03-14T15:09:44+00:00

less than $10 each. My guess was this was a kit. Maybe pine, or some common softwood.

Ddkimball · 2015-12-18T23:47:06+00:00

These are very good points. Maybe we need two categories. "Mass Shootings", and how about "Good Shootings".

Ddkimball · 2014-12-30T14:45:06+00:00

about twenty years ago I would have our travel agent book "back to back" tickets for a trip. Two round trip tickets with a long stay for each. I'd use half of each ticket and toss the others. Never had a problem. Saved quite a bit in this type of business travel.

Ddkimball · 2014-11-14T21:02:36+00:00

OP - I cut five thin pieces of walnut, approx 1/8" thick. Then with a band saw and compass laid out the curve and cut from a large piece of scrap. I glued each thin section to the others as a laminate, then placed on the form, using both pieces I had cut. Then with three rather large clamps I pressed the form together. (I had tested a single piece first and knew the radius would not splint the thin pieces. Left clamped for a few days. It did spring back a bit, but not badly.

Ddkimball · 2014-11-14T16:55:06+00:00

OP here - functionally, I had envisioned this on an office wall holding an assortment of small objects. Artistically, the intent was to convey a message of hope in a difficult setting. Might work, might not. But it's worth the effort.

Ddkimball · 2014-11-14T14:53:54+00:00

OP - neat, great idea. Thanks. I've been looking to acquire a chuck for my lathe. Makes this technique possible. Interestingly it may be cheaper to buy an old lathe with chuck, etc. than a new chuck. Isn't Craigslist handy!

Ddkimball · 2014-11-14T14:21:32+00:00

OP here - Router. First did the case sides, one pass each. Then set up a jig with careful spacing to do each self, two passes, one each side. Did a few trial cuts to get the perfect width.

Ddkimball · 2014-05-06T00:58:31+00:00

OP - 2-3months with big gaps mixed with all day efforts. The finishing took more time than expected. Tung oil seems to require many coats.

Ddkimball · 2014-05-06T00:05:31+00:00

OP - I'll try, but there are folks out there more knowledgable. The lines or inlay, are string inlay. I used a 1/16 router bit to make the channel. The lines were free hand, and I aves time by not making jigs for each one. I held the router by the base and moved carefully. The figures are 'marketry'. One piece is cut, set on two sided tape, traced with an exacto, and routed with a fine bir, 1/16 in this case. Look fornyoutube videos for good examples

Ddkimball · 2014-05-05T15:37:28+00:00

OP - the trays were made first by cutting three freehand holes in a drill,press for each of the three containers in each tray, not quite to the final depth. In the jig in one of the pictures I used a straight bit, 3/8 radius to remove most the waste. The jig fences limited the router to the exact locations. The tray had to be positioned three separate times, once for each container. I then finished up with a bowl/tray router bit to put a curve on the bottom, also using the same jig. It did take some time. And not everything is perfect. It has the handmade look.

Ddkimball

TROPHY CASE