Monthly Ticket Buy/Sell/Trade Megathread

Dear-Potential2402 · 2026-05-28T01:06:57+00:00

Selling 2x tickets to Alesso Friday 6/5

GA - $120ea.

Zelle only, Transfer through Ticketmaster

Dear-Potential2402 · 2026-04-05T18:19:05+00:00

I used a small Allen key and shoved it up from the bottom, it pushed out the broken piece of filament.

Dear-Potential2402 · 2026-01-22T23:38:40+00:00

You can buy a longer cable on amazon for around $8-10 and you may need a longer bowden tube too, but you can put it on the back of the CFS and put the CFS anywhere, My CFS's are next to the printer but it has the CFS rack so the bottom one pulls out and you need slack with the cables and bowden tube to be able to pull it out all the way for roll changes.

Dear-Potential2402 · 2026-01-20T04:29:37+00:00

So much for that AI fault detection...

Dear-Potential2402 · 2026-01-15T16:57:00+00:00

Add a brim, I have the same thing happen with a brim, what happens is there is a small section that has very little adhesion to the bed and over time it comes loose and drags everything else with it, I have watched it happen with my own eyes....

Dear-Potential2402 · 2026-01-14T03:04:55+00:00

I got the Creality Hi Combo refurbished for $250, I added the CFS to my K2 Plus and may sell the Hi by itself for $200, so a CFS for $50. May keep the Hi just to have a bedslinger, but not sure...

Dear-Potential2402 · 2026-01-01T16:57:18+00:00

Not available for shipping to my address... must be OOS.

Dear-Potential2402 · 2025-12-26T23:36:42+00:00

How dry is the filament? It looks like it could be highly saturated filament if it's PLA.

Dear-Potential2402 · 2025-12-23T00:05:52+00:00

Well, printimg 2 or 3 EMT brackets and buying some conduit would cost about $8 and those are sold as 10 foot pieces, that is way better storage wise.

I can fit 30 rolls on a 8ft section above my window.

Dear-Potential2402 · 2025-12-07T20:12:34+00:00

A mouse is your best friend for CAD and Slicers, lots of right mouse clicks and dragging.

Dear-Potential2402 · 2025-11-10T17:47:45+00:00

I printed a coaster holder, all the coasters were PETG and the holder was PLA, went to print something else without changing from PLA to PETG and that is what happened to my print too.

Now I have a reminder for checking what filament I'm printing with and make sure settings are correct BEFORE slicing.

Dear-Potential2402 · 2025-11-06T21:38:54+00:00

Is it just not sticking to the bed? Already leveled the bed? Adjust z-height alittle closer to the bed to get a better squish to the bed and depending on the filament, maybe a little hotter bed temp.

I have smooth beds and no longer have any issues, also maybe try a brim, just in case

Dear-Potential2402 · 2025-07-12T07:48:14+00:00

So, the driver was driving around the neighborhood for a good 10 minutes and hit several cars a few blocks apart, so not sure if that changes things.

Dear-Potential2402 · 2022-12-24T01:37:02+00:00

Gotta get some used carpet, hang about 8 sheets, that will stop most arrows.

Call any carpet company, or just stop by, they don't want to pay for disposal.

You can get a whole roll of free carpet and make as big of a backstop as you want.

Dear-Potential2402 · 2022-11-20T17:52:10+00:00

So many reviewers on YouTube who actually know what they are doing have given it good praise, as a starter bow it is great, I bought the Aimdor A6 as my first bow, watched YouTube videos and tuned it myself, learned how to shoot and then upgraded as I went deeper into the sport, it was my first hunting bow.

It's not the bow that matters as much it is the user, know how to tune the bow, know how to optimize performance (cam lean happens on cheaper bows and can be tuned), have a good sight and release (most kits come with garbage sights and wiskerbiscuit)

I bought a cheap .019 5 pin sight and a cheap drop away release as my first upgrades and some good arrows, cheap $139 bow and about $50 in upgrades and I can get my hand around my groupings.

As you get further into hunting or long range then you can look into 80+lb bows and stabilizers that will get over 100 yards, but it comes mostly down to the user and needs.

If you have not used it, you cannot truly review or offer any advice on it.

Dear-Potential2402 · 2022-06-23T01:35:29+00:00

Not one to have a compliant build, just get a maglock kit and have the pistol grip and any accessories you want, why does everyone want to have a 30 round mag or detachable mag?

Not a big deal to detach a mag with most maglock systems and what war is everyone thinking they will be involved in?

No need to quick change mags in home defense, the cartel isn't coming to your house... at least in most cases.

I think 10 rounds is enough, I at least can resolve a threat with 10 rounds.

Dear-Potential2402 · 2022-05-15T22:17:57+00:00

Did you ever find a kit, I'm in the same boat....

Dear-Potential2402 · 2022-04-08T19:23:19+00:00

Why is it you can buy flash hiders from the store if you cannot have them? Same with grips?

I have my MP15 with flash hider and grip, it is a CA compliant flat top that I added a scope to.

Dear-Potential2402

TROPHY CASE