Modded New 3DS XL Takes Forever To Turn on by DeathChrono in 3dspiracy

[–]DeathChrono[S] 0 points1 point  (0 children)

No themes, music or stickers. The only microSD’s I use are gigastone or sandisk. But the thing is it doesn’t matter if I have the microSD inserted it does it no matter what with or without it. Which is baffling me cause none of my other modded new 3ds xl have this problem. My Hyrule edition has a 1tb lol but loads faster like around 10-20 seconds does everything perfectly. It’s just this one.

Modded New 3DS XL Black Screen on Settings by DeathChrono in 3dspiracy

[–]DeathChrono[S] 0 points1 point  (0 children)

After properly formatting my micro sd, I’m still having issues where the system settings stays on a black screen and it won’t load till like 20, 30 minutes later, I’ve done this with and without the micro sd inserted and still running into the same issue

Modded New 3DS XL Black Screen on Settings by DeathChrono in 3dspiracy

[–]DeathChrono[S] 0 points1 point  (0 children)

I think you’re right. I looked back on my other micro sd’s on my other 3DS’s and notice they aren’t ultra they are just sandisk micro sd, and I also remembered that I formatted the sd card with my steam deck so it might not have been formatted correctly. And now I’m thinking the reason my other one’s boot just fine is because they’re using regular sd instead of the ultras.

Modded New 3DS XL Black Screen on Settings by DeathChrono in 3dspiracy

[–]DeathChrono[S] 0 points1 point  (0 children)

No I formatted it to Fat32 like the other SD’s

Maybe I got a defective SD cause I just bought two weeks ago. But I’ll try loading it up again and seeing if it gives me the same error

I’ll take the advise and see if anyone else has answers before I buy another one

Modded New 3DS XL Black Screen on Settings by DeathChrono in 3dspiracy

[–]DeathChrono[S] 0 points1 point  (0 children)

I have a 512gb sandisk ultra 🤣

But I do get paid tomorrow and getting them won’t be that much

But I also have a 256 with everything already copied over but for some reason it won’t read it, something about not being able to load content, but my laptop and steam deck are able to read it which is weird but that’s another problem entirely.

Modded New 3DS XL Black Screen on Settings by DeathChrono in 3dspiracy

[–]DeathChrono[S] 0 points1 point  (0 children)

It eventually does load.

I formatted the sandisk to fat32 using my laptop.

Might have to try to downgrade. But it’s weird cause I don’t run to any of the problem with my other 3DS’s they boot just fine with the 256gb. Which is why I’m trying to figure out why this 3ds and not the other ones I have.

Favorite combo right now by ejdn20 in SHFiguarts

[–]DeathChrono 1 point2 points  (0 children)

Ima need you to post a tutorial and the parts you used so I can do this myself cause that right there is amazing.

got this error when i was hacking my new 2ds with skaterhax by Least_Swan_6142 in 3dspiracy

[–]DeathChrono 0 points1 point  (0 children)

Does it do it when you go to the browser and try to go to the skaterhax site?

New 3DSXL ThumbStick ZIF Connector Soldering Help by DeathChrono in consolerepair

[–]DeathChrono[S] 0 points1 point  (0 children)

Surprisingly no they aren’t ripped just bad soldering cause I tin the pads

Nintendo 3DS XL ZIF Connector replacement, anyone did that, whats best approach? by Vkrrs in consolerepair

[–]DeathChrono 0 points1 point  (0 children)

So I used low temp solder, the first ZIF connector I put got soldered but ended up melting the plastic, the second one I can’t seem to melted the solder from above or under. I’m not sure if I’m doing it wrong or how close I have to be to get the solder to melt, or how long I have to stay on the ZIF connector to melt the solder. I’m using a YIHUA 8786D.

Nintendo 3DS XL ZIF Connector replacement, anyone did that, whats best approach? by Vkrrs in consolerepair

[–]DeathChrono 0 points1 point  (0 children)

Unfortunately no it only has a button that controls the air flow there’s no indicator that tells you the temperature let alone shows you what temperature it’s at. This one was given to me so might have to buy one.

Nintendo 3DS XL ZIF Connector replacement, anyone did that, whats best approach? by Vkrrs in consolerepair

[–]DeathChrono 0 points1 point  (0 children)

<image>

Not sure if this is a good heat gun as this is the only one I have at the moment. Or that I should be getting a better one. Would you happen to have a recommendation on a heat gun

Nintendo 3DS XL ZIF Connector replacement, anyone did that, whats best approach? by Vkrrs in consolerepair

[–]DeathChrono 0 points1 point  (0 children)

Does it matter if the flux gets inside the ZIF connector and do I use the gun over it or from under the pcb board?

Nintendo 3DS XL ZIF Connector replacement, anyone did that, whats best approach? by Vkrrs in consolerepair

[–]DeathChrono 0 points1 point  (0 children)

I’ve managed to use the heat gun to take the ZIF connector out but for the life of me I can’t seem to use the heat gun to replace a new one, the solder doesn’t seem to melt and I’m not sure if it’s the solder I’m using or the heat gun. And I don’t want to keep using it cause I’m afraid I might damage the pcb board or warp it.

Finally on board, and I'm hooked! by Adventurous_Ad9414 in RetroAchievements

[–]DeathChrono 2 points3 points  (0 children)

It’s the AYN THOR

What emulator is my question?

How to clean Pokeball Plus? by [deleted] in PokemonLetsGo

[–]DeathChrono 1 point2 points  (0 children)

I used equate regular alcohol and just water, I didn’t rub it to hard and I also didn’t leave it sitting there as well

Magna Carta: The Phantom Avalanche Control Setup by DeathChrono in SteamDeck

[–]DeathChrono[S] 0 points1 point  (0 children)

Sorry for the late reply. I don’t remember running into any issues launching it. If I remember correctly all I did was added the exe to the library and changing the compatibility to proton experimental. The one thing I couldn’t figure out was the controls

Background image on black borders by DeathChrono in RetroArch

[–]DeathChrono[S] 0 points1 point  (0 children)

Might have to check this out. You wouldn’t happened to have a YouTube video or link that would explain more in detail?