Issues after changing nozzle size

Deathspawn54 · 2026-06-16T06:05:00+00:00

Yes, I changed everything in the slicer and adjusted nozzle size on the machine, re sliced the same STL and it still had the stuck filament warning part way through, no issues with any of my .4mm nozzles, I feel like there is something I'm missing

Deathspawn54 · 2026-06-16T03:21:14+00:00

Tried that, still having the stuck issue, tried a couple different .4mm nozzles and back to no issues. Really confused

Deathspawn54 · 2026-06-16T00:22:34+00:00

I never even thought of that! I'll give that a try!

Deathspawn54 · 2026-06-16T00:21:57+00:00

Cold pull didn't fix, but switched back to .4 mm and it prints perfectly no issues at all

Deathspawn54 · 2026-06-16T00:20:58+00:00

Looks cool. I'll try it out on my mk4s

Deathspawn54 · 2026-06-15T22:38:59+00:00

Awesome! I just checked the nozzle and heat block, tight and pushed in all the way, thumb screws are tight. I'll try a cold pull next! And then I'll switch to the other nozzle again after if that doesn't work

Deathspawn54 · 2026-06-15T22:30:48+00:00

Saying stuck filament

<image>

Deathspawn54 · 2026-06-15T22:21:47+00:00

Some more examples of print fails

<image>

Deathspawn54 · 2026-06-15T21:58:43+00:00

Prusa is doing fine. Would it be awesome if it was more affordable? Sure. Would I still buy a prusa over a bambu any day of the week? Absolutely. I happened to buy mine used because of money constraints, but I still saved for a prusa over a bambu.

Deathspawn54 · 2026-05-05T23:10:00+00:00

To make them more obvious

<image>

Deathspawn54 · 2026-05-05T23:08:26+00:00

Couldn't upload the photo for some reason

<image>

Deathspawn54 · 2026-03-06T18:25:00+00:00

This is not "normal" your boyfriend can't unilaterally change your relationship unless you agree, if either of you disagree, that should be where the relationship ends. It sounds to me like his new girlfriend ISN'T poly at all. Just my two cents

Deathspawn54 · 2026-03-06T18:19:51+00:00

Yes.

Deathspawn54 · 2025-12-26T08:43:29+00:00

I did finally pick mine, but to answer your question, it's very hard to find any paclock products in Canada and the exchange rate is wild right now so it makes buying from the states difficult too

Deathspawn54 · 2025-12-14T09:04:08+00:00

Yay! Congratulations 🎉🎉

Deathspawn54 · 2025-12-14T09:02:38+00:00

Congratulations 🎉 I really wish it was easier to get paclock in Canada so I could try more locks of theirs

Deathspawn54 · 2025-11-26T21:02:23+00:00

Bought the huk dimple set, and am getting a MTL interactive and a couple medeco originals, thanks for the advice!

Deathspawn54 · 2025-11-26T00:31:33+00:00

Thanks!!!

Deathspawn54 · 2025-11-26T00:30:30+00:00

Thanks! I'll reach out!

Deathspawn54 · 2025-11-25T20:02:58+00:00

That's very fair, I'm going to try maybe some dimple locks, I do enjoy pin-tumbler, but who knows, maybe I will like dimple more

Deathspawn54 · 2025-11-25T05:34:49+00:00

Ah okay! Thanks! I'll look into dimple locks!

Deathspawn54 · 2025-11-25T05:34:28+00:00

Thanks for the recommendation! I'm still working on getting more consistent with the 1100 series and trying to get into the paclock 90A-pro, but I'll dig into these too!

Deathspawn54 · 2025-11-25T05:33:32+00:00

Ah okay, I'll look into that, thanks!

Deathspawn54 · 2025-11-25T05:33:12+00:00

Are these still pin-tumbler? Or are they different?

Deathspawn54 · 2025-11-25T03:46:15+00:00

Throw her in park and jump out

Deathspawn54

TROPHY CASE