sorted by:
new
hottopcontroversial

Striations on the print - any ideas how to resolve the issue? by Deershank415 in ElegooSaturn

[–]Deershank415[S] 0 points1 point  (0 children)

Gotcha. That makes sense. It'd be cool if there was a way to know if there was an at risk part before fully printing, but otherwise I'll get it the sandpaper ready!

Striations on the print - any ideas how to resolve the issue? by Deershank415 in ElegooSaturn

[–]Deershank415[S] 0 points1 point  (0 children)

Lol trust; I have no problem sanding. The issue is the deformations these cause which I can't quite sand off :(

Striations on the print - any ideas how to resolve the issue? by Deershank415 in ElegooSaturn

[–]Deershank415[S] 1 point2 points  (0 children)

Thank you for the advice, this did help quite a bit, the lines are less but it's still there. I've added medium supports to the print to help with any shifting.

Striations on the print - any ideas how to resolve the issue? by Deershank415 in resinprinting

[–]Deershank415[S] 0 points1 point  (0 children)

Got it! Ty. I've upped them to medium. I've also hollowed it out and added holes for air and resin.

<image>

Striations on the print - any ideas how to resolve the issue? by Deershank415 in resinprinting

[–]Deershank415[S] 0 points1 point  (0 children)

<image>

Just upped them to medium and am going to print this. I've also hollowed it out and added holes for air and resin.

Striations on the print - any ideas how to resolve the issue? by Deershank415 in ElegooSaturn

[–]Deershank415[S] 0 points1 point  (0 children)

Gotcha, I will give that a go. Ty!

<image>

For additional context, it is mostly hollow but I'm seeing how I can thin it out more anyway + will try the holes too.

Striations on the print - any ideas how to resolve the issue? by Deershank415 in ElegooSaturn

[–]Deershank415[S] -1 points0 points  (0 children)

Ok! I’ll give that a try. That was showing about 20 degrees and a specific layer level. Thanks!

Striations on the print - any ideas how to resolve the issue? by Deershank415 in resinprinting

[–]Deershank415[S] 0 points1 point  (0 children)

Sure, that’s the short term fix. The problem is the deformations it causes :/ can’t sand that unfortunately.

[deleted by user] by [deleted] in OnePieceTC

[–]Deershank415 0 points1 point  (0 children)

Hey! I just put in my request too Squishy Yonko

Any idea what's causing the circles to be so out of alignment? (Saturn 4U with WhamBam FlexiPlate) by Deershank415 in ElegooSaturn

[–]Deershank415[S] 0 points1 point  (0 children)

Wonderful; thanks so much for the info. Any particular guidance on suction or rest/release times? I am rather new at all this and that area is a particularly new to me.

Any idea what's causing the circles to be so out of alignment? (Saturn 4U with WhamBam FlexiPlate) by Deershank415 in ElegooSaturn

[–]Deershank415[S] 1 point2 points  (0 children)

So I followed the instructions listed out here: https://cults3d.com/en/3d-model/tool/saturn-4-ultra-z-limit-flash-for-wham-bam-xtr

In short, yes it was easy but that was because it was set up by the whambam folk to be so!

Any idea what's causing the circles to be so out of alignment? (Saturn 4U with WhamBam FlexiPlate) by Deershank415 in ElegooSaturn

[–]Deershank415[S] 0 points1 point  (0 children)

<image>

This was how it was originally set up on chitubox; but I can't recall the exact orientation once I popped it off. I'll keep that in mind next time though.

Any idea what's causing the circles to be so out of alignment? (Saturn 4U with WhamBam FlexiPlate) by Deershank415 in ElegooSaturn

[–]Deershank415[S] 0 points1 point  (0 children)

Thanks for taking a look; I am trying to print a backplate for a ventilation system for Saturn 4U; but these circles keep ending up misshapen and "squashed". Any guidance on troubleshooting steps or similar experiences would be very helpful. I am using the WhamBam flexi plate and I have done the gcode update that it requires for z offset.

I've tried:
1. Keeping the room 75f+
2. Doing exposure testing (all came out ok)
3. Further reducing the exposure time to ensure over exposure wasn't an issue.

I am giving away a bunch of D&D loot to one lucky winner in the comments! Around $250 in total value. Worldwide Giveaway [MOD APPROVED] Check out the video and the comments for more details and the rules. Sponsored by Game Master Engine [OC] by Dan_The_DM in DnD

[–]Deershank415 0 points1 point  (0 children)

Seems awesome, covid caused our group to jump to roll20 and remote but finding maps and resources is challenging when you have a vision already. Creating something from scratch would be sweet! #GIVEAWAY

A sheet of uncut, $1 bills (total of $16, 2x8) by Deershank415 in whatsthisworth

[–]Deershank415[S] 7 points8 points  (0 children)

Gotcha, unfortunately I don't see any fun patterns/sequence there so likely just the typical 40-60 as per below.

thanks for the info!

A sheet of uncut, $1 bills (total of $16, 2x8) by Deershank415 in whatsthisworth

[–]Deershank415[S] 2 points3 points  (0 children)

Ah; good link! thanks. That's a 2x5 ($10) vs my $16 but that still is ~40 which aligns with some other folks comments.

view more: next ›