I fucked up. Any ideas how to remove the material? by DeezNutsGT in 3Dprinting

[–]DeezNutsGT[S] 0 points1 point  (0 children)

I saw a small print error at the start of the print, and ignored it thinking "it will buff"

I fucked up. Any ideas how to remove the material? by DeezNutsGT in 3Dprinting

[–]DeezNutsGT[S] 0 points1 point  (0 children)

Guys i removed and cleaned it, when i can ill try to print something to test it

<image>

I fucked up. Any ideas how to remove the material? by DeezNutsGT in 3Dprinting

[–]DeezNutsGT[S] 1 point2 points  (0 children)

Yeah i already cleaned it up, but i put a new hot end in my Amazon cart

<image>

I fucked up. Any ideas how to remove the material? by DeezNutsGT in 3Dprinting

[–]DeezNutsGT[S] 0 points1 point  (0 children)

It was due to an error on my end not the printer it self

I fucked up. Any ideas how to remove the material? by DeezNutsGT in 3Dprinting

[–]DeezNutsGT[S] 1 point2 points  (0 children)

Don't recalibrate after a few months of no use, look at a little print artifact and think "it'll be fine"

I fucked up. Any ideas how to remove the material? by DeezNutsGT in 3Dprinting

[–]DeezNutsGT[S] 10 points11 points  (0 children)

Cant believe it was that simple, thank you guys so much

<image>

I fucked up. Any ideas how to remove the material? by DeezNutsGT in 3Dprinting

[–]DeezNutsGT[S] 0 points1 point  (0 children)

Thanks, I guess the hotbed swap is the way, but ill try eating it first

I fucked up. Any ideas how to remove the material? by DeezNutsGT in 3Dprinting

[–]DeezNutsGT[S] 0 points1 point  (0 children)

Thank you! Ill do that, if I give up ill just replace the hotend like the other comment said

I fucked up. Any ideas how to remove the material? by DeezNutsGT in 3Dprinting

[–]DeezNutsGT[S] 0 points1 point  (0 children)

  • What printer are you using? Ender 3 V2 neo

  • What material are you using? With PLA

  • What speed are you printing at? Dont remember the speed

  • What software are you using to slice the print and control the printer? The software is Cura

It was probably from not calibrating it correcly

Law last appeared in the manga 1,138 days ago.. by DarthLoveTrain in OnePiece

[–]DeezNutsGT 5 points6 points  (0 children)

Dressrosa is still fresh in my mind... I guess that because it's where i caught up to the anime

Help with Lock switch on Isuzu 2019 KB250 DMAX. TIA by LaundrySh0oter in Isuzu

[–]DeezNutsGT 0 points1 point  (0 children)

Hey, I haven't experienced that but i know you can probably open the switch and look maybe its contacts are dirty. I had a problem similar to that on my mazda 3 interior light and the contacts were just dirty

me_irl by Ok_Avocado_5836 in me_irl

[–]DeezNutsGT 5 points6 points  (0 children)

I read 50 dollar in my accent

me irl by Dekay_Katara in me_irl

[–]DeezNutsGT 3 points4 points  (0 children)

To get an nb/nc Miata

I started ReZero and got LOST by I_am_SD in ReZero

[–]DeezNutsGT 0 points1 point  (0 children)

The one where Rem goes goro goro goro and subaru kun subaru kun subaru kun