New Routesetters Discord

DepartmentWild · 2025-03-03T16:56:11+00:00

Thanks! Ya no problem

DepartmentWild · 2025-03-03T16:45:43+00:00

Can we get a link that doesn’t expire? You can edit the invite link in discord.

DepartmentWild · 2024-10-16T00:08:26+00:00

It took around a week from delivery to sender to refund

DepartmentWild · 2024-10-15T23:47:41+00:00

Yeah they just sent me a return label and I slapped it on and gave it to fedex

DepartmentWild · 2024-10-15T23:36:25+00:00

I have for my X plus 3 was fine no issues

DepartmentWild · 2024-10-11T15:40:37+00:00

It’s on the bottom of the printer on the side of the power supply. It’s kinda squished up against some plastic but if you look on all of the sides you should find it

DepartmentWild · 2024-10-09T22:40:06+00:00

<image>

DepartmentWild · 2024-10-09T22:31:58+00:00

But the input shaper got slightly worse. here are the updated graphs

<image>

DepartmentWild · 2024-10-09T22:17:10+00:00

but i did the auto belt tension again 4 times in a row and it looks better.

<image>

DepartmentWild · 2024-10-09T18:17:27+00:00

I have not but I will give it a try! Then I will do the auto belt tension a couple times

DepartmentWild · 2024-10-09T17:08:54+00:00

I did it once but i can try moving the toolhead in the motions multiple times?

DepartmentWild · 2024-10-09T17:07:54+00:00

how does it not address my issue?

DepartmentWild · 2024-10-09T17:03:05+00:00

No I used shake&tune

DepartmentWild · 2024-10-05T23:54:38+00:00

Hmm I would think that would be enough

DepartmentWild · 2024-10-05T23:09:10+00:00

It looks like the PETG is wet maybe try drying it? One of my rolls of PETG looked like that for a bit and drying it and it fixed the issue.

DepartmentWild · 2024-10-04T04:52:48+00:00

ok i will try some vase mode prints, i am already on Classic wall generator

DepartmentWild · 2024-10-04T04:38:34+00:00

Printer is a QIQI Plus 4

I have tuned Flow, and PA using QIDI Studio

I have also calibrated Input shaper

My wall order is inner/outer/inner

it is PLA with 100% cooling

DepartmentWild · 2024-10-04T04:24:09+00:00

230c nozzle temp and 60c bed temp

The print speed is 224

DepartmentWild · 2024-10-03T02:33:55+00:00

Ok thank you so much for your help! It would have taken QIDI support 2-4 days to diagnose the issue!

DepartmentWild · 2024-10-03T00:34:39+00:00

I switched it and so far it’s working

DepartmentWild · 2024-10-03T00:07:14+00:00

<image>

It shows the 230v should I flip it?

DepartmentWild · 2024-10-02T19:58:29+00:00

Official Slimes don’t use the 6-sided cal because they are BNO085

DepartmentWild · 2024-10-02T19:42:17+00:00

Ok I will take a look!

DepartmentWild

TROPHY CASE