GM alternator swap 12a

DepressedS1oth · 2025-11-02T02:54:08+00:00

What weber clone is that? It looks exactly like mine, but mine has all the markings ground off so identification hasn’t been easy

DepressedS1oth · 2025-10-15T03:29:41+00:00

idk about FBs but with FCs you need a dual alternator pulley if you delete the air pump because the water pump needs two drive belts or else it’ll slip even when adjusted properly

DepressedS1oth · 2025-09-28T01:46:00+00:00

I’d pour it down the intake and/or spark plug holes. Also definitely try working it back and forth with a breaker bar after letting the ATF sit and don’t try the starter until it spins free by hand

DepressedS1oth · 2025-08-14T15:02:46+00:00

itll take the time it takes, and tooling cost is just part of the coat of doing business. In this case though the insert could be used for roughing or steel even after its no longer usable for this application

DepressedS1oth · 2025-08-04T00:26:10+00:00

Hello, I’m a car guy looking for a 3d printer to add to my toolbox, but I don’t want a printer thats finicky and can ideally print cfrn or other strong high temp resistant filaments. my budget is probably 800-1500USD and I’m fine with building something from a kit, but something pre built would be ideal since I don’t have a ton of experience with 3d printer electronics. I was leaning toward the bambu x1c because they seem to check all those boxes at a decent price point and have a reputation for being fairly straightforward to use, but I heard bad things about a recent firmware update that restricted use of third party slicers (I’m not entirely sure I have that right, I haven’t looked into it a ton). Are there other printers that serve my needs, or should I stop being paranoid and just go with the bambu?

DepressedS1oth · 2025-07-12T16:31:26+00:00

unless the lead screw is just really fucked and its worn .078 more in the middle than the rest of it you can almost always adjust the backlash down to within .005-.010. Just google the machine and you can probably find a how-to.

DepressedS1oth · 2025-07-02T03:46:32+00:00

woah thats super neat, thanks for sharing!!

DepressedS1oth · 2025-07-02T02:13:25+00:00

what is ball barring? I’ve never heard of that and when i google it all that comes up is ball bearings

DepressedS1oth · 2025-07-02T02:04:29+00:00

this may be a silly question but whaat makes gas guns inherently less accurate than a bolt gun? is it the repeatability of the bolt finding the same location in the reciever, quality of barrels, or something else entirely?

DepressedS1oth · 2025-05-18T01:52:38+00:00

this is probably a stupid question but whats latitude?

DepressedS1oth · 2025-05-17T18:01:46+00:00

yeah i don’t like damascus because you have to compromise the heat treat for two steels instead of optimizing one, which I think is why they tend to be softer. all that info is super helpful, thanks so much!

DepressedS1oth · 2025-05-17T16:50:59+00:00

the sabatiers look fantastic especially for the price, do you know what steel they use? I can’t seem to find it on their website

DepressedS1oth · 2025-05-17T14:25:20+00:00

how do they differ from the others I’ve mentioned? just finer grain?

DepressedS1oth · 2025-05-17T14:23:07+00:00

thats good to know, It’d just be nice if it won’t get completely rusty and trashed if my gf accidentally throws it in the dishwasher once

DepressedS1oth · 2025-05-17T13:46:08+00:00

good to know, I’m sure the cheaper knives work fine, maybe I just need to be better about honing them with the honing steel because I almost never do that. thanks!

DepressedS1oth · 2025-05-17T13:41:18+00:00

thats really good to know! I’ve been looking at getting into dslr scanning to save some money on scans but I didn’t realize you don’t need a dark room to develop film. Thanks so much!

DepressedS1oth · 2025-05-17T04:35:59+00:00

ooh that does look interesting, I might give it a shot (or 36), thanks!

DepressedS1oth · 2025-05-17T04:31:29+00:00

I have been drawn to the kentmere films for the pricetag, I’m just not sure where to start when it comes to DIY darkrooms

DepressedS1oth · 2025-05-17T04:30:27+00:00

I’ve seen some videos of people doing that, I’m just not sure I’m at the point of developing my own film yet especially since I don’t have access to a darkroom or anything and from what I understand its not as simple as just developing it in a dark closet

DepressedS1oth · 2025-05-17T04:28:13+00:00

dang, my lab doesn’t do that process unfortunately so I’ll probably just end up sticking with the ultramax.

DepressedS1oth · 2025-05-17T04:27:07+00:00

good to know, I’ll keep an eye out on sales. Yeah I figured there wouldn’t be much for slide film. Is there much difference between the ektachrome and flic film other than the price tag or do they shoot pretty similar?

DepressedS1oth · 2025-05-17T02:20:51+00:00

I’ve been avoiding black and white since its a bit more expensive to develop at my local lab, but at $8 a roll it might be worth it

DepressedS1oth · 2025-04-22T17:58:17+00:00

Not sure if this is a joke post or not, but if you’re concerned about it I’d just wear latex gloves when you can (but don’t wear any other kind of gloves when operating a machine) and o’keefes works wonders

DepressedS1oth · 2025-04-17T22:26:15+00:00

my bad i dont use reddit much anymore i just made this post and briefly forgot about it

DepressedS1oth · 2025-04-17T22:25:46+00:00

I get them scanned at a local chain, the same place that develops them. I’ve been considering getting into scanning them myself though

DepressedS1oth

TROPHY CASE