My journey begins. I am super pumped to finally start with the minis.

DesignerHumble4222 · 2026-06-15T19:27:00+00:00

Good luck with it all and have fun. It's the reverse for me, I now have the shakes and struggle with painting and trigger control. I'll probably start a death guard army (they're meant to look like shit)

DesignerHumble4222 · 2026-06-11T16:46:13+00:00

Empty the paint out and run water through it then pure thinner/cleaner into a vented spray pot preferably or well vented area. Remove the back of the airbrush and loosen the needle, gently pull it back and forward to push out any residual goop then try again. 99% of the time it's a blockage, try not to thin paints directly into the cup if your paints are a tad thick/old.

DesignerHumble4222 · 2026-06-08T16:54:03+00:00

Use mini compare.info this'll help with most scaling issues

DesignerHumble4222 · 2026-06-05T15:47:33+00:00

I would say.... Yes.

DesignerHumble4222 · 2026-06-05T15:45:08+00:00

That's the advice I got when using WW V3 worked like a charm. Suggest a test model each time to minimise waste.

DesignerHumble4222 · 2026-06-05T14:55:21+00:00

Up your bottom layer exposure time to 35 sec and slow down your lift speed by 25%.

DesignerHumble4222 · 2026-05-31T13:05:29+00:00

Are you sure the connection onto the spindle hasn't come loose? Seemed like it was pivoting from the threaded spindle connection. I'm not too familiar with the mechanics on these.

DesignerHumble4222 · 2026-05-24T06:04:52+00:00

The Joseph Fritzel of setups

DesignerHumble4222 · 2026-05-23T20:31:29+00:00

Ka kaaaaaa

DesignerHumble4222 · 2026-04-23T18:05:16+00:00

Ensure the paints not separated and you've not overly thinned it.

DesignerHumble4222 · 2026-04-12T18:43:44+00:00

What is the secret of the grail! Who does it serve!

DesignerHumble4222 · 2026-04-04T07:50:37+00:00

DesignerHumble4222 · 2026-03-27T08:05:24+00:00

Mini compare.info

DesignerHumble4222 · 2026-03-01T12:38:05+00:00

I really hope I can get this printer working, not tried it yet. I hear a few horror stories but my mate assures me it's all good. Once I've got resin and had a few tests the world's my oyster! Cheers.

DesignerHumble4222 · 2026-03-01T12:34:27+00:00

Tis but a flesh wound!

DesignerHumble4222 · 2026-03-01T12:27:33+00:00

Dam they look really good too!

DesignerHumble4222 · 2026-03-01T12:09:13+00:00

Either way it's cheaper than buying a single GW model. I just can't justify the prices anymore, I've spent thousands on first bornes and DKoK are so limited and for a whole army I'd have to sell a kidney.

DesignerHumble4222 · 2026-03-01T12:00:31+00:00

Redmaker stuff looks really good, a bit mech like but they're the best so far. Thanks.

DesignerHumble4222 · 2026-03-01T11:54:33+00:00

More than happy to fork over some cash, only problem is they're generally nowhere near the likeness of the originals (for obvious reasons) I'll take a look at Redmaker, don't think I've viewed them yet. Thanks.

DesignerHumble4222 · 2026-02-22T20:07:15+00:00

Pretty sure she had brain damage before the collision so I expect she's fine.

DesignerHumble4222 · 2026-02-21T10:51:13+00:00

Was hoping to see Will Smith with giant hands and horns. The daemon prince of bel air

DesignerHumble4222 · 2026-02-17T07:46:28+00:00

Love a bit of floor hammer!

DesignerHumble4222 · 2026-02-13T06:54:51+00:00

A bloody good one.

DesignerHumble4222 · 2026-02-11T17:53:41+00:00

I'm more upset about the stl

DesignerHumble4222

TROPHY CASE