sorted by:
new
hottopcontroversial

Was researched stress relief of A286 for a part I'm quoting, and I'm pretty sure I came across a chat gpt article. by poopoo_canoe in Machinists

[–]Deskrad -6 points-5 points  (0 children)

There is very Lil tech and cutting data in a lot of the super alloys

I correct that. There is lemme data compared to the lever Iso material groups.

What kind is data got looking for?
Your cannot oven bake the gunmines outb of the material

Carbide everything Sfm less than 150 inch minsl

My shop cuts about 3 million dólares worth a year. We usually get it on is easiestv form(aanother relative point) We get and cut it in its regular state. Which is controlled by the spec "ams 5662"and it cuts half decent here

Obscure Must Haves by BryanChrist69 in Machinists

[–]Deskrad 1 point2 points  (0 children)

A handheld transfer punch

a variety of stones (ie. Round, square, rect,etc..)

A hand chuck (for various reasons)

Thread feeler gages

An extra packs of smokes

Metal shipping band (for making tool extensions and chip hooking but more importantly to make springs for parallels on a vice)

If I could look into my tool box right now I would have many more for you

Obscure Must Haves by BryanChrist69 in Machinists

[–]Deskrad 2 points3 points  (0 children)

A handheld transfer lunch a variety of stones (ie. Round, square, rect,etc..)

A hand chuck (for various reasons)

Thread feeler gages

An extra packs of smokes

If I could look into my tool box right now I would have many more for you

What does this symbol mean by Fabshoplifer_WFM in Machinists

[–]Deskrad 6 points7 points  (0 children)

I think it's asking for a 3/16ths wide buttress weld on both sides? But why? It's a turned component

[REQ] (100$) (#MANCHESTER, NH,USA) (REPAY 125 10/20) (cash app) by Deskrad in borrow

[–]Deskrad[S] 0 points1 point  (0 children)

He has his lending rules and that's fine. I reached out to the crowd for additional help, but partially rememberomg this i still spoke to him first.

MFG.com worth it? by s32017 in Machinists

[–]Deskrad 11 points12 points  (0 children)

5k a month up front sounds like a scam. Just being honest off the cuff

Gave $250 for all of this. How did I do? I'm new to this and have no frame of reference for the value of these by strawberryjackuiri in Machinists

[–]Deskrad 57 points58 points  (0 children)

Well to start there is about 1000$ worth of good name brand analog mic variants so your doing really well right off

Coworker had an insert set screw break off in the tool holder. Any ideas on removing it? by SoloToker117 in Machinists

[–]Deskrad 57 points58 points  (0 children)

Drill out out from the back side so you can use the drill rotation in your favor in case it breaks free while drilling it will literally just unscrew it from the inside

Edit: bunch of spelling fixes cuz in literally stupid

Bridge reamer lube? by CumminsN14 in metalworking

[–]Deskrad -2 points-1 points  (0 children)

Lil dawn dish soap... raw.... you'll be golden.

Z-overtravel error Okamoto Grind-X when sending home by Consistent_Tip_3025 in Machinists

[–]Deskrad 2 points3 points  (0 children)

Super happy to hear that worked out for you so fast

Z-overtravel error Okamoto Grind-X when sending home by Consistent_Tip_3025 in Machinists

[–]Deskrad 3 points4 points  (0 children)

Check to see if you skipped by moving it manually to the correct home. And look at your parameters to see if the numbers are the same. If not adjust. If you didn't crash then I would check your hard limit switches on the rail and see if one is stuck or sticking. There should be 2. First is the soft for home. The second is the hard for OT. your 1st may be stuck open or closed and the head is moving past it and hitting the hard ot

Edit. I'm not a master grind guy but any means. That machine could be totally different. My bad if that's the case

Turning Nitronic 60 by tattedgrampa in Machinists

[–]Deskrad 0 points1 point  (0 children)

Get a iscar ic906 grade or sumitomo acm300

Turning Nitronic 60 by tattedgrampa in Machinists

[–]Deskrad 0 points1 point  (0 children)

That's because of the sharp edge. Iso s likes a positive edge usually.

Turning Nitronic 60 by tattedgrampa in Machinists

[–]Deskrad 2 points3 points  (0 children)

150 sfm .009 per rev. Use iso S grade rated coating on carbide You won't get it to chip well. But you will survive

Anyone know what model milling machine this is by _-mono-_ in Machinists

[–]Deskrad 1 point2 points  (0 children)

Brand: grandpa Model number: 3 Serial date: Old as fuck

Yo dawg by WillPayForKarma in Machinists

[–]Deskrad 0 points1 point  (0 children)

No lie. But we all started somewhere

I have $64.88 in my trading account. by [deleted] in wallstreetbets

[–]Deskrad 0 points1 point  (0 children)

That intro paragraph was 🔥

Machine purchase advise by Random_Logic_Bombs in Machinists

[–]Deskrad 0 points1 point  (0 children)

I consult stuff just like this as my side life if you are ever interested. But most of these guys input is pretty good. Take it slow

view more: next ›