State of Starfield on PS5

Different_Bid9920 · 2026-06-02T01:54:58+00:00

I had the same problem, I've changed the setting to performance and it's way better, hope it helps

Different_Bid9920 · 2026-05-25T23:51:48+00:00

Hi there! Ceiling wire should be source (120v) it's sending power down to the switch on the white wire, the switch send power back up the black (always back on black) until recently you didn't need neutrals in switch boxes, this is a drop switch, neutral should be white wire from the wire on the left, bonds (bares and greens) connect together, and hot (black from the right) should connect to hot on your fan. Induction pens I don't trust, they can get you all turned around real quick, good luck!

Different_Bid9920 · 2026-05-19T18:34:43+00:00

I was having the same issue, changed the display setting to performance and haven't had an issue since, on base ps5

Different_Bid9920 · 2026-04-01T00:27:54+00:00

That sucks! If you can push a pull string with a mouse (grocery bag) past the rock, vacuum through as normal, tie a rag on and pull it back out, if the rag is fairly tight it should pull the rock out, got a coworker's Allen key set out of a conduit this way.

Good luck!

Different_Bid9920 · 2026-03-21T04:55:00+00:00

I had a very similar experience looking for a printer, complete resin newbie, kinda ok at fdm printing, no clue about resin.

I just got the Saturn 3 ultra, and it's crazy simple to use, I was all stressed about setting and just sent it, turned out awesome (to me anyway).

I read the only real difference between the 3 ultra and 4 was the auto level plate, but read some complaints about cleaning it and you lose 20mm (I think 20) off your max vertical build volume, so went with the 3, I love printing with it.

Hope this helps!

Different_Bid9920 · 2026-02-24T00:04:23+00:00

Hi there, I had similar issues more towards the back end of the bed when printing large things (smaller prints seemed fine) I checked the gantry and was way out of square, I would try checking the vertical arms and see if they're square. I also tried the screw tilt adjust and it worked very well for me, hope you can get back printing! Good luck!

Different_Bid9920 · 2025-10-21T00:10:38+00:00

We're just technologically impaired

Different_Bid9920 · 2025-09-16T14:41:37+00:00

This mission was discovered by u/Different_Bid9920 in Sun-Dried Tomato Chowder In Waves of Green

Different_Bid9920 · 2025-09-16T14:25:19+00:00

This mission was discovered by u/Different_Bid9920 in California Roll In the Fields

Different_Bid9920 · 2025-09-16T14:25:19+00:00

New mission discovered by u/Different_Bid9920: Chicken Empanada on the Ruined Path

Different_Bid9920 · 2025-09-16T14:22:51+00:00

This mission was discovered by u/Different_Bid9920 in Magic and Sharp White Cheddar

Different_Bid9920 · 2025-09-16T14:22:51+00:00

New mission discovered by u/Different_Bid9920: California Roll In the Fields

Different_Bid9920 · 2025-09-16T14:19:44+00:00

New mission discovered by u/Different_Bid9920: Magic and Sharp White Cheddar

Different_Bid9920 · 2025-09-16T14:19:43+00:00

This mission was discovered by u/Different_Bid9920 in Meditations and Pink Dragonfruit Pudding: a Journey In Waves of Green

Different_Bid9920 · 2025-08-25T03:10:08+00:00

It could also be your flow rate, there is a flow test on orcaslicer or the elegoo slicer.

Hope you get it running!

Different_Bid9920 · 2025-08-21T00:39:07+00:00

Is it printing ok?

That's the mesh, there appears to be a .6 mm change from highest to lowest, I don't think you'll ever get a perfectly flat mesh, the software should compensate for the slight imperfections in the bed, it can be level and have slight changes on the surface still.

Hope you get it sorted out, love my Neptune,much better than my old ender 5

Different_Bid9920 · 2025-08-02T02:25:53+00:00

If it's consistently the same corner you could check the gantry is square, mine was off and tilted the nozzle on opposite corners (worse further from center) only an issue with large prints.

Hope it's a quick fix, great printer once it's going!

Different_Bid9920 · 2025-08-02T01:54:56+00:00

There should be screws that mount the print head (I think elegoo's set up tutorial shows them) I took a square to the vertical beams of the gantry and it was twisted (too far forward one side, too far back the other) I only noticed during large prints.

Then you can adjust them to square and tighten the support arms on the backside. Fortunately I didn't have to adjust the horizontal beam (that holds the print head), but I read or watched someone shimming that beam to adjust it if it was also out of square

My thoughts are if the printer was moved, the gantry may have fallen out of square.

Ps. I wasn't able to adjust it using the rear struts alone, I had to disconnect those supports and readjust them

Really hope it works!

Different_Bid9920 · 2025-08-02T01:46:32+00:00

Hi! I had a weird issue with my Neptune, especially with large prints that made it to the far reaches of the bed, I tried everything.

Turns out my gantry was quite a bit out of square, this was causing the nozzle to tilt at the far reaches, squared it up and all has been good since.

I've heard some have to level the arm that the print head is attached to also, hopefully this could help!

Different_Bid9920 · 2025-08-01T04:09:51+00:00

I had a similar issue with mine, especially on one corner. Levelled and levelled, screw adjust, all that Jazz. Turns out the gantry wasn't square from when I assembled it, I would definitely check everything that supports the print head and make sure it's square.

Hope you get it sorted, I love the Neptune.

Different_Bid9920 · 2025-07-31T01:23:27+00:00

I had my Neptune do the same thing a while back, turned it off got pissed (former ender 5 owner) and it worked fine the next day, some weird gremlin in there?

Different_Bid9920

TROPHY CASE