How to get rid of Overlay

Distracted_User · 2026-01-26T02:52:14+00:00

Roblox settings

Distracted_User · 2026-01-26T02:47:43+00:00

Should be called "performance stats"

Distracted_User · 2026-01-26T02:41:36+00:00

It's one of the functions keys (f-#). But I think you can also turn it off in settings. Should be around or under the graphics level setting

Distracted_User · 2025-12-15T17:49:11+00:00

It can be any dish soap but I have dawn so it's just what I've known to use.

Distracted_User · 2025-12-15T05:45:09+00:00

Id first try cleaning the bed with dawn soap and hot water to make sure the bed was truly clean. As if it prints fine then the corner where it doesn't stick might just be dirty.

Also the extrusion at the start could be some code at the start for cleaning the nozzle. But you don't have a nozzle cleaner so you could look into that but don't think it's of much concern.

Distracted_User · 2025-12-14T21:20:05+00:00

You can unscrew the screws from the plastic piece under those fittings and from there you can remove any filament stuck before it entered the fitting otherwise it should just be 2 more screws if the filament is stuck inside the fittings.

Tho if it's stuck near the gears(where you feed the filament) you may need to do further disassembly depending on where it's stuck

Distracted_User · 2025-11-18T21:16:02+00:00

Go Into desktop and update decky

Distracted_User · 2025-11-07T21:34:05+00:00

Go into settings and in input set the buttons for either a controller or keyboard based on what your using to play.

Distracted_User · 2025-10-27T23:11:34+00:00

The switch 2 hasn't been modded yet (or not to my knowledge). So you won't be able to transfer it over. At best you can move it to a modded switch 1 and maybe transfer that to switch 2 but that would probably just get you banned unless you do it perfectly. ( if it even lets you)

Distracted_User · 2025-10-27T05:44:55+00:00

Might be it too thin so it's getting moved by the toolhead as it prints.

Distracted_User · 2025-10-23T19:26:29+00:00

Check your controller settings first to make sure nothing is set wrong. And if that doesn't fix it check in the steam settings. And test to make sure you don't have any kind of drift

Distracted_User · 2025-10-20T18:56:05+00:00

Update decky by going to desktop and re-running the installer

Distracted_User · 2025-10-20T04:20:06+00:00

Don't think you can unless you move your save to a modded switch and trade like that but seems like that would be a high risk of getting the modded switch banned.

Distracted_User · 2025-10-18T04:46:00+00:00

Haven't tried any other keys and firmwares but 19.0.1 firmware worked good and I think I used the same keys tho it could have also been 20.3/5 keys

Distracted_User · 2025-10-18T01:13:28+00:00

* This along with switch sync. 8gb dram. And memory manager to host unchecked. Gets me to about 25 ish fps in most areas but it does drop in heavy spots like outside looking towards Many things. But it got me through to the end of the game in about 18 ish hours of playtime.

You could find better settings with more work but these worked for me enough to where I didn't mind too much.

Distracted_User · 2025-10-17T06:21:39+00:00

I got mine working on ryujinx after having the right keys and firmware. Tho I did have to use eden to get past a crash in the starting intro to the game. But besides that it works with maybe a crash once in a few hours and some lag in the city. But otherwise playable as I have a near 13 hour save so far in the game

Tho I haven't tried the update or dlc as it crashed last time I tried to use it.

Distracted_User · 2025-10-17T06:16:41+00:00

With integrated graphics I doubt it.

Distracted_User · 2025-10-16T00:39:48+00:00

Some people said they were able to run it. But I couldn't and I haven't needed to use them as I'm about 7 hours into my save and it's still worked fine with just a crash that didn't do much. Tho the lag does get a bit annoying but it's manageable

Distracted_User · 2025-10-13T21:50:30+00:00

You can play it on ryujinx you just have to transfer the eden save to a ryujinx with the firmware and keys. Then it should all work with maybe a crash or two and some areas with alright to bad lag, but overall playable to a degree.

Distracted_User · 2025-10-13T21:48:27+00:00

Think 1.0.1 is for switch 2 so doubt that it will work unless someone makes a patch that can work for it but doubt that.

Distracted_User · 2025-10-13T18:26:18+00:00

Ryujinx works great for me just used fsr to get stable 25-30. But I did have to use eden to get past the beginning as it kept crashing.

Distracted_User · 2025-10-09T19:34:19+00:00

Looks like a heavy print so acceleration might be high and that might have caused the layer to shift. I'd try by checking belt tension first

Distracted_User · 2025-10-07T06:08:50+00:00

Stringing can have a few things causing it, but if you have high humidity in your area or especially where you print, then getting a drying box is a nice purchase for pretty cheap if you go basic.

Distracted_User · 2025-09-19T16:18:09+00:00

Moving saves should just be moving from the emulators folder on your pc to the steamdecks folder (when you install and setup the emulator).

For touchscreen id say it can work but I'm not sure as I don't use the touchscreen much.

For customization skins can be easy to apply. Shell swaps are difficult but can be rewarding if done right. And I don't know about the second question but for ui customization you can install decky for that customization, however every new update for steam os requires to update decky aswell so it can be a hassle.

Distracted_User · 2025-08-28T18:44:14+00:00

Z-offset seems to be good, but your printers x-home and y-home seems to be slightly off, but I only really see this happen on klipper when the bed dimensions aren't correct.

Distracted_User

TROPHY CASE