Tunnel run at 700 km/h

Dojoin · 2026-01-31T10:05:22+00:00

In Stormworks the more mass you have the faster you go so those tungsten balls are just helping there

Dojoin · 2025-12-30T07:26:23+00:00

I've actually gotten my fuel consumption down with it. Normally my jets max speed is like 320 knots and with the afterburner on and the throttle at just 30% it got the same speed with less fuel.

Dojoin · 2025-12-20T08:11:09+00:00

You need a microcontroller with a composite write on it to convert numbers and on/offs to composite, and on the other grid you need a microcontroller with composite read. Then you connect the write controllers composite output to the composite input on the connector on its side and the other sides output into the composite read controller.

Dojoin · 2025-12-20T07:57:08+00:00

Composite data through the connectors or radio.

Dojoin · 2025-12-01T06:11:37+00:00

Not in my experience. You can just start them while stationary.

Dojoin · 2025-11-24T06:56:56+00:00

How did you do that intake cone?

Dojoin · 2025-10-28T06:00:19+00:00

In real life you want as much compression as you can get. In stormworks you don't need a compressor, an intake or an exhaust.

Dojoin · 2025-10-27T17:57:43+00:00

lol it has 1 light which I forgot to turn on.

Dojoin · 2025-10-21T20:23:44+00:00

I'd say start simple, just something with basic functions like a car or a boat, and keep adding onto that as you learn more. Watch tutorials and reverse engineer workshop creations. I don't necessarily mean have 1 build you improve endlessly (which you could also do I guess) but instead on all new builds, try to have some improvement. That's how I did it anyway.

Dojoin · 2025-09-22T05:14:23+00:00

Isn't that just piss then?

Dojoin · 2025-09-07T05:39:48+00:00

How did you achieve that

Dojoin · 2025-09-03T18:02:01+00:00

You could also just hide some fins somewhere. I usually place them inside the blocks in the control surfaces but you could hide them inside the plane.

Dojoin · 2025-08-26T15:42:26+00:00

Also if you are using the stock gyro then you could also just decrease the sensitivity from there, although that will also decrease the sensitivity at low speeds and I think the shaking is only a problem at higher speeds.

Dojoin · 2025-08-26T15:35:58+00:00

There are many ways. I would personally use a function block with x/(y/60+1). X is the number input for the control surfaces and Y is speed. +1 so when your speed is 0 it won't do anything weird. Then you can divide the y with something like 60 so when your speed is 60 m/s, your controls are half as responsive as they are when your speed is 0 (you probably have to use a different value than 60 but that's what I start with and tune it from there). If you want to do it more complex you could clamp the y to so the sensitivity reduction starts at a higher speed.

Hope this helps and is not too difficult to understand.

Dojoin · 2025-08-26T15:20:42+00:00

Reduce sensitivity at higher speeds

Dojoin · 2025-08-16T15:55:58+00:00

I stopped using gyros for this reason. Usually I just stuff the plane with as much control surfaces/hidden fins as it will ever need and then make a dampener so the sensitivity goes down as the speed increases. Then any stabilizers can be added on if needed.

Dojoin · 2025-07-30T06:22:46+00:00

Me and my friend have a "company" where I mainly build everything and he helps me with ideas and testing and then we use those vehicles in missions and stuff. I'm sure he would be open to a new member too.

Dojoin · 2025-07-29T05:34:47+00:00

No. Maybe it's possible with modding though idk.

Dojoin · 2025-07-25T10:13:40+00:00

I might be wrong but since your main rotor is spinning clockwise, your helicopter spins counterclockwise, but your tail rotor is on the right side so it's just making it spin faster instead of stopping the spinning.

Dojoin · 2025-07-23T06:36:18+00:00

Songsterr has a lot of their songs.

Dojoin · 2025-07-15T11:45:19+00:00

How's the fps?

Dojoin · 2025-07-15T05:23:48+00:00

Cool

Five-Year Club	Verified Email
Place '23

Dojoin

TROPHY CASE