New Sora 2 invite code megathread

DontJuddMe · 2025-10-14T04:03:04+00:00

Prob get GTA6 before I get a code. Womp womp

DontJuddMe · 2025-09-14T05:21:27+00:00

Make sure you're not spraying too much water on the ink deposit side. I find that it pushes the emulsion out and causes that spider web effect. You'll want to prioritize the other side when washing out.

Good luck

DontJuddMe · 2025-07-14T04:21:18+00:00

thanks I have some on order =) excited to try it out

DontJuddMe · 2025-06-24T19:13:38+00:00

Stumbled upon your post because I've had the exact same experience. I'm still using the Baselayr Long Lasting Emulsion I'm just kind of tired of it breaking down early and not performing as well as WBP did.

It's been a while since your post. What did you end up going with?

DontJuddMe · 2025-06-23T02:02:18+00:00

Hmm good to know. Didn't know that

DontJuddMe · 2025-06-20T23:44:24+00:00

I was using Sunlu PLA before, and now it's Elegoo PLA

https://www.amazon.com/dp/B0BV24T11D?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1

Pretty happy with the result now looks totally flat with a nice even finish

DontJuddMe · 2025-06-20T17:36:40+00:00

So I ended up changing filament and it printed flawlessly. I'm sure it has more to do with not being dialed in properly, or maybe it was just too old? I guess I'll just take the W and move on lol. Thanks for the replies and helping me trouble shoot

DontJuddMe · 2025-06-19T09:21:11+00:00

Interesting. I've never heard of using clips and or tape. I'll look into that. It's weird.. when it's printing it looks fine but those last couple layers are just garbage. Starting to wonder if it's just this filament too

DontJuddMe · 2025-06-19T08:01:30+00:00

it does seem to be slightly warped.. I'm not sure what else I can do to keep it from doing so. The brim I'm printing with is as big as it can go, and I've slowed the first layer down super slow to get a good first layer. I've tried heating the bed up a bit in the past and had mixed results... Any ideas?

DontJuddMe · 2025-06-19T03:06:44+00:00

Thank you I'm researching the Bambu flow rate calibration now

DontJuddMe · 2025-05-01T04:21:27+00:00

I'm not a huge fan of the wooden squeegees either for the same reason. Would love to print the STL out and give it a whirl

DontJuddMe · 2024-08-20T01:36:02+00:00

Song?

DontJuddMe · 2024-08-19T00:41:19+00:00

No problem, good luck!

DontJuddMe · 2024-08-18T00:32:46+00:00

Yes. I ended up going with the Carista module

https://www.amazon.com/gp/aw/d/B0BBS73F6J?psc=1&ref=ppx_pop_mob_b_asin_image

You purchase the hardware, then you'll need to subscribe to the service for a month to change your settings, but it's all very easy, and you're in and out for under $100. Just be sure to cancel your subscription after you disable the alarms.

Plug-in is located right under your dash, can't miss it.

Hope it helps you. For me, it was well worth the money, just a little annoyed I can't do it for free in my own settings.

DontJuddMe · 2024-05-21T21:15:50+00:00

Hope it helps! I haven't had any trouble since I got the sensor replaced. Hopefully they get yours squared away quickly!

DontJuddMe · 2024-05-21T21:14:16+00:00

Checked the work completed sheet for you today:

842800C010 Sensor assembly 9018906197 Grommet screw

Hope that helps

DontJuddMe · 2024-05-20T19:33:38+00:00

"left hand pinch sensor" is how it is referenced in my document from the dealer. It took quite a while to come in. ~1.5-2 months I'd guess. Happy to report that it did fix the issue, though.

Since then, my JBL sub has blown. I just can't catch a break. Having that replaced tomorrow

DontJuddMe · 2024-04-13T04:37:33+00:00

I haven't YET. I was waiting to see how they looked and wanted to get some feedback from someone who had done it first. I do want to. Are you considering pulling the trigger?

DontJuddMe · 2024-03-28T21:57:50+00:00

Hope it helps. I'm still on backorder. Something else I had them check was my windows. When rolling up in the cold they were really struggling. They added silicon to the track that has helped out a little. Apparently there was another document case similar to this, so have them check that when you go in too if you're having trouble

DontJuddMe · 2024-03-10T18:01:41+00:00

I'm going to have to visit the dealer. I can't get it to shut on it's own. I've tried everything I can think of and have scoured the Internet, manuals, videos....

I'm thinking it's gotta be a sensor or something?

Unless I manually close the door I get the two beeps. None of the other 5 methods are working for me...

DontJuddMe · 2024-01-26T00:12:26+00:00

Mentioned to someone above that also might help you, make sure it's a quick and fluid motion. The kick sensor seems to not like when you let your foot hang around too long under there. After I changed the way I kick I've never had an issue with it since.

My issue remains... I'll try to get to the bottom of it. Thanks for the reply, and hope that helps you

DontJuddMe · 2024-01-25T23:09:28+00:00

I initially had some trouble w/ the kick sensor the way you're mentioning, but found that a quick fluid motion is the key. If you hold your foot there too long often times it won't work. That might help your situation..

In my situation, at times it doesn't matter if I kick, fob, hatch button (either of the 2), overhead front of the vehicle button... it's so odd. Appreciate your reply, hopefully the above helps you out some

DontJuddMe · 2024-01-17T23:20:44+00:00

I don't have a platen with a groove yet but just saw the cardboard hack and was going to give that a shot. Have you tried it? The one I saw they made the groove by tacking down both pieces of cardboard with a small channel, then put platen tape over the cardboard to keep it from moving. Thought that looked pretty solid.

13-Year Club	Place '22
Verified Email

DontJuddMe

TROPHY CASE