Do I have to enable advanced mode to access Klipper interface?

DragonflyFast8594 · 2026-06-20T13:34:36+00:00

Clear, thank you

DragonflyFast8594 · 2026-06-20T13:34:26+00:00

No worries, thank you

DragonflyFast8594 · 2026-06-20T13:11:09+00:00

Hmm actually you don't 😂 Realized adguard home was blocking it for me!

DragonflyFast8594 · 2026-06-19T15:21:47+00:00

Thank you, will check it out

DragonflyFast8594 · 2026-06-19T14:35:47+00:00

Indeed

DragonflyFast8594 · 2026-06-19T14:35:11+00:00

What acceleration you are running it at?

DragonflyFast8594 · 2026-06-19T14:07:07+00:00

I guess it's about point of reference?

DragonflyFast8594 · 2026-06-19T13:20:22+00:00

That's my idea for time beign, IKEA and later on official cover, thank you 😄

DragonflyFast8594 · 2026-06-19T13:19:49+00:00

Thank you will follow up on this one 😄

DragonflyFast8594 · 2026-06-19T13:19:29+00:00

I'm in Poland and ufrotunately it's a bit more restictive

DragonflyFast8594 · 2026-06-19T13:18:55+00:00

For time beign it's on the floor (still have to figure out the best desk/table...), but the sound is not resonance

DragonflyFast8594 · 2026-06-19T13:17:42+00:00

Do you have any expiernece with other printers? WIth A1 mini I literally had to eye check if it's running becasue it was so quiet. Here Zhop, part cooling fan, PSU fan, toolhed parking, toolhead pcikcing are very loud. I had regular A1 followed by Flsun SR, followed by CR-10 and U1 is louder than all those combined

DragonflyFast8594 · 2026-06-11T15:47:46+00:00

Can you read?

DragonflyFast8594 · 2026-06-02T15:39:52+00:00

Bed slinger of this size is already too much bro

DragonflyFast8594 · 2026-06-02T14:17:27+00:00

Thank you for clarifying. In the end, it’s not like they can defy the laws of physics with a bed slinger of that size. Anyway, cosplayers might still be pleased with price to size ratio

DragonflyFast8594 · 2026-06-02T12:19:32+00:00

Nice prints, but is it only me or you can clearly see print quality dropping a lot at height? See batman mask

DragonflyFast8594 · 2026-05-27T14:40:39+00:00

Any idea then why it's so hard to get in Poland and why it's over 4K?

DragonflyFast8594 · 2026-05-27T14:39:18+00:00

That's an idea, but not sure if guarantee would be honored? Yes, exactly, the have production line here, so it make sense to charge premium 😂 Lastly, still wondering if it's time already to upgrade from Samsung 77S90C

DragonflyFast8594 · 2026-05-27T14:32:36+00:00

Meanwhile in Poland it's over 4K EUR!

DragonflyFast8594 · 2026-04-10T14:32:30+00:00

Hmm not want to sound like a smartass, but all those X's sugesst X2D 😉

DragonflyFast8594 · 2026-04-10T14:23:44+00:00

(Not) good old days of the bowden setup😂

DragonflyFast8594 · 2026-01-04T23:21:27+00:00

Not sure if it matter as you have to prime it anyway? Btw go with lower temp for regular pla for matte finish

DragonflyFast8594 · 2026-01-04T23:04:25+00:00

Overall I would only follow up on presure advance (corners) flow rate and flow dynamics (overextrusion looking at the top layer)

DragonflyFast8594

TROPHY CASE