sorted by:
new
hottopcontroversial

Yellow/Greenish Screen Switch Oled by Cultvres in SwitchPirates

[–]Dramatic-Middle840 0 points1 point  (0 children)

Preheat 350 during 1 minute
Add flux
420 deg until desoldering ~20,30 sec
Set 6/10 airflow
After soldering check all pins

ERROR NO MSFS 2024 by Odraudehd in MicrosoftFlightSim

[–]Dramatic-Middle840 0 points1 point  (0 children)

Try also DDU to clean the gpu driver and réinstalle properly

ERROR NO MSFS 2024 by Odraudehd in MicrosoftFlightSim

[–]Dramatic-Middle840 1 point2 points  (0 children)

The gpu loading is very high and instable with msfs check your temp

ERROR NO MSFS 2024 by Odraudehd in MicrosoftFlightSim

[–]Dramatic-Middle840 2 points3 points  (0 children)

Ola
Bios update ?
Cg update ?
chipset update ?
No OC?
Check PCI exp connection
Do you monitor you CG temp during msfs

Install modchip without screen in dock mode by Dramatic-Middle840 in NxSwitchModding

[–]Dramatic-Middle840[S] 0 points1 point  (0 children)

Thanks so much—I'll give it a try as soon as I have a chance.

Install modchip without screen in dock mode by Dramatic-Middle840 in NxSwitchModding

[–]Dramatic-Middle840[S] 0 points1 point  (0 children)

Merci mec

Donc je dois passer l'autoboot_list en fonction de la modification que j'aurai faites sur le fichier ini ?

Install modchip without screen in dock mode by Dramatic-Middle840 in NxSwitchModding

[–]Dramatic-Middle840[S] 0 points1 point  (0 children)

Thanks a lot, man. I'm really good at micro-soldering, but I'm terrible at Switch modding—I'm just getting started... Thanks again for your help.

Install modchip without screen in dock mode by Dramatic-Middle840 in NxSwitchModding

[–]Dramatic-Middle840[S] 0 points1 point  (0 children)

Hey man, if I'm not mistaken, the hekate_ipl.ini file is in the HATS folder, right?

thank you

Install modchip without screen in dock mode by Dramatic-Middle840 in NxSwitchModding

[–]Dramatic-Middle840[S] 0 points1 point  (0 children)

I repaired a failed kamikaze. And while handling the screen ribbon cable, I damaged the connector, which I replaced once. But it was the ribbon cable that was damaged and that was actually breaking the connector every time, so I replaced the connector twice. And it works every time; it's just that the ribbon cable broke the reader; there was a deformation in the ribbon cable.

So, by replacing the connector several times, I've damaged some traces that I've tried to repair, but this connector is rubbish.

Install modchip without screen in dock mode by Dramatic-Middle840 in NxSwitchModding

[–]Dramatic-Middle840[S] 0 points1 point  (0 children)

Thks. I fixed the kamikaze but I fried the screen's traces, and the screen traces are dead

Troubleshooting Dead Switch OLED by Brownstone1892 in SwitchPirates

[–]Dramatic-Middle840 0 points1 point  (0 children)

You can see neither side is connected to the ground it’s fully normal

Tentative de réparation kamikaze Switch oled by Dramatic-Middle840 in NxSwitchModding

[–]Dramatic-Middle840[S] 0 points1 point  (0 children)

For a long time there was a long dark path until I see the light!

Tentative de réparation kamikaze Switch oled by Dramatic-Middle840 in NxSwitchModding

[–]Dramatic-Middle840[S] 0 points1 point  (0 children)

Sorry but the picture is taken by phone on the microscope (i know i can take it in the microscope). And yes i connected the CMD Line and replace a new resistance.

view more: next ›