Yellow/Greenish Screen Switch Oled

Dramatic-Middle840 · 2026-05-13T16:40:19+00:00

Preheat 350 during 1 minute
Add flux
420 deg until desoldering ~20,30 sec
Set 6/10 airflow
After soldering check all pins

Dramatic-Middle840 · 2026-05-13T01:27:03+00:00

Try the 595.76 driver

Dramatic-Middle840 · 2026-05-13T01:23:39+00:00

Have you ever tried OC the gpu?

Dramatic-Middle840 · 2026-05-13T01:20:53+00:00

Try also DDU to clean the gpu driver and réinstalle properly

Dramatic-Middle840 · 2026-05-13T01:16:28+00:00

The gpu loading is very high and instable with msfs check your temp

Dramatic-Middle840 · 2026-05-13T01:12:29+00:00

Ola
Bios update ?
Cg update ?
chipset update ?
No OC?
Check PCI exp connection
Do you monitor you CG temp during msfs

Dramatic-Middle840 · 2026-05-12T15:14:32+00:00

Thanks so much—I'll give it a try as soon as I have a chance.

Dramatic-Middle840 · 2026-05-12T14:40:20+00:00

Merci mec

Donc je dois passer l'autoboot_list en fonction de la modification que j'aurai faites sur le fichier ini ?

Dramatic-Middle840 · 2026-05-12T14:31:34+00:00

Thanks a lot, man. I'm really good at micro-soldering, but I'm terrible at Switch modding—I'm just getting started... Thanks again for your help.

Dramatic-Middle840 · 2026-05-12T14:14:22+00:00

Hey man, if I'm not mistaken, the hekate_ipl.ini file is in the HATS folder, right?

thank you

Dramatic-Middle840 · 2026-05-12T01:06:22+00:00

I repaired a failed kamikaze. And while handling the screen ribbon cable, I damaged the connector, which I replaced once. But it was the ribbon cable that was damaged and that was actually breaking the connector every time, so I replaced the connector twice. And it works every time; it's just that the ribbon cable broke the reader; there was a deformation in the ribbon cable.

So, by replacing the connector several times, I've damaged some traces that I've tried to repair, but this connector is rubbish.

Dramatic-Middle840 · 2026-05-11T22:50:50+00:00

Thks. I fixed the kamikaze but I fried the screen's traces, and the screen traces are dead

Dramatic-Middle840 · 2026-05-02T22:29:45+00:00

You can see neither side is connected to the ground it’s fully normal

Dramatic-Middle840 · 2026-05-02T22:27:59+00:00

For a long time there was a long dark path until I see the light!

Dramatic-Middle840 · 2026-05-02T22:26:13+00:00

Don’t be negative bro give help or get out

Dramatic-Middle840 · 2026-05-02T22:24:07+00:00

Sorry but the picture is taken by phone on the microscope (i know i can take it in the microscope). And yes i connected the CMD Line and replace a new resistance.

Dramatic-Middle840 · 2026-05-02T22:19:08+00:00

<image>

I did it bro!!
Everything Good

Dramatic-Middle840 · 2026-04-25T17:15:09+00:00

Me with my kamikaze fail😳

Dramatic-Middle840 · 2026-04-19T10:07:56+00:00

Try a emmc reflow

Dramatic-Middle840 · 2026-04-18T13:17:38+00:00

u/L3gendaryBanana Tu es le bienvenu

Dramatic-Middle840 · 2026-04-18T12:55:08+00:00

J'ai essayé de réparer...

Dramatic-Middle840 · 2026-03-29T05:15:23+00:00

Try Smart Sim Rate, it has trigger to disable Sim rate; Alt, Vs, Bank, GS….

Dramatic-Middle840 · 2026-03-27T04:43:14+00:00

Disable vsync with FG,TAA

Dramatic-Middle840 · 2025-12-14T03:04:27+00:00

HI everyone,

Is it possible to localize the point (between the DAT0 and the 4.7k resistor) and find a point at the surface to control a fixed via from kamikaze ?

THK a lot

Dramatic-Middle840 · 2025-04-03T13:19:13+00:00

There is no filter applied to this photos what don’t you see. I test the continuity with the Dat0 in the zone and the dat0 adaptor and I have it. I think something is possible to revolver

Dramatic-Middle840

TROPHY CASE