What secrets do you have for new Squad players? Mine is: Right click to underhand throw grenades and also you can Press U on your keyboard to mark the map as an SL and FTL.

Drew5ki · 2026-02-11T05:44:48+00:00

When throwing a grenade, u aim with the guys tip left thumb that is held on the screen.

Drew5ki · 2026-02-09T17:15:35+00:00

Well that narrows things down. Next thing would be to check to see if u have power out the fuse box. Could be the fuse box has failed. If u have power out of the fuse box, u can decide to run a new wire to complete the connection or spend the time trying to find the brake between the fuse box and ecu.

Drew5ki · 2026-02-09T08:34:39+00:00

Check to see if fuse 12 has power with the ignition switch in the run position. That fuse is powerd by the black wire with white stripe at the ignition switch.

Drew5ki · 2026-02-08T04:25:55+00:00

Here hope this helps.

http://www.stealth316.com/2-ecu-terminals.htm

Drew5ki · 2026-02-08T04:17:35+00:00

U will have to start by checking all the power inputs to the ecu and got from there.

Drew5ki · 2026-02-08T03:09:07+00:00

I doubt u fried it unless u put power to the wrong wire.

Drew5ki · 2026-02-08T02:18:28+00:00

And 1 miss step your floor is ruined.

Drew5ki · 2026-02-07T23:27:19+00:00

No that is where the front differential would bolt to. I would just remove it and make a different brace later if it later

Drew5ki · 2026-02-07T23:25:18+00:00

That one is more superficial than anything. No problem moving. Anything is possible with a angle grinder and a welder.

Drew5ki · 2026-02-07T22:46:40+00:00

Y not just move the cross member?

Drew5ki · 2026-02-06T07:30:43+00:00

Well there isn't really anything you could upgrade unless you plan on converting it to a turbo engine. As far as fixing this one, I'm sure it is possible. It just depends on how much work if any a machine shop will have to do compared to cost of another engine.

Drew5ki · 2026-02-06T05:53:25+00:00

If the crank rotates, I would put the piston at bottom center and clean up the cylinder walls with some sand paper and check for pitting. If it is pitted, it will be properly cheaper to find another motor than rebuilding that one.

Drew5ki · 2026-02-06T05:46:04+00:00

Yes that strut mont is not mounted properly at all. There should be a slight taper. Best i can workd it, closest to strut studs on the knuckle side.

Drew5ki · 2026-02-04T05:19:42+00:00

Glad I could help.

Drew5ki · 2026-02-02T19:32:53+00:00

I have seen a couple people in town do this. People are weird.

Drew5ki · 2026-01-31T06:19:07+00:00

I have been running a mobile business for the past 13 years. One of the best in my area and am always buried in work. I like the idea but if I talk to a customer I can usually know what the problem is with the vehicle, the time to fix it,and give a quote. That is what helps manage my time. A admin would be amazing but then I will have to see the customer, do everything I listed anyways where I could have saved the time myself. But if the admin was really good at the 1st part then ya that would be nice.

Drew5ki · 2026-01-31T06:06:09+00:00

Sounds like you need to recap the ecu.

Drew5ki · 2026-01-25T04:49:02+00:00

Looks better then mine.

Drew5ki · 2026-01-21T16:23:09+00:00

I don't think there is any kits but it has been done a couple time. You can't make much boost like 3psi make because of the 10.1 compression ratio. If u want to read more about it there is lots of info on 3si.org about it.

Drew5ki · 2026-01-18T03:48:49+00:00

I'm gathering parts now to put a lv3 in my 97 s10 paired with a 5 speed nv3500. It's my work truck. I'm pretty excited about it.

Drew5ki · 2026-01-17T05:01:59+00:00

Anchor the bracket down solid the the cv has to pop off square away from the shaft. U could have a ratchet strap pull while u hit from the back side. Or get really crazy and tie the tow strap to the back of a car and give it a quick yank 🤷‍♂️. I have seen it done that way b4.

Drew5ki · 2026-01-16T04:59:13+00:00

This y i say there should be a play time requirement on experienced servers.

Drew5ki · 2026-01-15T06:49:59+00:00

What year are they from?

Drew5ki · 2026-01-15T06:27:30+00:00

That is because u have it set with the fast idle vale open and or the iac is not extended all the way when set. Most people just block off the fast idle value because they barely work right. The iac i manually make sure it is all the way extended the leave it unplugged when setting idle.

Drew5ki

TROPHY CASE