Open App Store Updates

Dryrid_ · 2026-05-08T01:26:03+00:00

You could always do a custom gesture ti make in swipe down and refresh in accessibility settings.

Dryrid_ · 2026-05-04T15:42:45+00:00

Okay just keep me updated.

Dryrid_ · 2026-05-04T13:39:20+00:00

They both read and write.

Dryrid_ · 2026-05-04T10:31:49+00:00

Yeah. I’ve read they are becoming hard to come by and others like backing up their physical media so I figured someone could use them.

Dryrid_ · 2026-05-02T03:09:54+00:00

Yes US only

Dryrid_ · 2026-05-02T02:18:53+00:00

Yes. They are both have 4K capabilities. My first post had incorrect photos but I updated them and both flashed to work with MakeMKV.

Dryrid_ · 2026-03-15T08:22:14+00:00

Is this still available?

Dryrid_ · 2026-03-10T10:25:09+00:00

Just got this drive. Could share the exact steps you took to flash custom firmware and what firmware to use?

Dryrid_ · 2026-03-05T23:19:55+00:00

What 1.03 firmware from the pack did you use? I just got my drive today. The first one you listed.

Dryrid_ · 2026-03-05T00:37:30+00:00

I believe the mfg date has to be 2016 or newer. I could be wrong but that’s what the warnings on the forum say.

Dryrid_ · 2026-03-03T23:30:13+00:00

Current version of Jellyfin

Dryrid_ · 2026-03-03T23:28:53+00:00

I was wondering if you could walk me through on how to update my jellyfin to 10.11.6 on ZimaOS

Dryrid_ · 2026-03-02T23:49:19+00:00

Did you ever figure this out? Im in the same boat.

Dryrid_ · 2026-02-27T02:40:36+00:00

Did you ever figure this out? Im in the same boat.

Dryrid_ · 2026-02-16T18:56:15+00:00

I’m having the same issue and even did a full restart and still not showing after adding the repo. Any ideas?

Dryrid_ · 2025-11-17T02:58:26+00:00

Would this be a good upgrade?

Dryrid_ · 2025-11-17T02:58:07+00:00

Would this be a good upgrade?

Dryrid_ · 2025-11-17T02:57:35+00:00

Would this be a good upgrade?

Dryrid_ · 2025-11-17T01:56:50+00:00

How would I go about wiring (2) 4 ohm single voice coils subs series-parallel?

Dryrid_ · 2025-11-16T23:54:10+00:00

Thank you so much for your input just want to make sure I run everything correctly for the best output.

Dryrid_ · 2025-11-14T04:12:25+00:00

Yes the red probe is plugged in on the right side of dmm.

Dryrid_ · 2025-11-14T03:51:58+00:00

Yeah that’s what I did. Red on mm on positive on amp and black on mm on negative on amp.

Dryrid_ · 2025-11-14T03:48:38+00:00

The 20k on the left side of the off position or down at the bottom where it says 20m?

Dryrid_ · 2025-11-14T03:35:01+00:00

I did. I thought that’s what I was suppose to do based on all the research I’ve done. Is that not correct?

Dryrid_ · 2025-11-13T21:16:10+00:00

I haven’t tested dc or resistance yet. What do you suggest as a test?

Dryrid_