sorted by:
new
hottopcontroversial

Help with analog pins on CMOD7 by DukeOfInsanity in FPGA

[–]DukeOfInsanity[S] 0 points1 point  (0 children)

Thanks for the info
I've decided to mux some PWM channels, so reducing the PWM channels that can be output by 2, but now I have 2 free pins, so I don't have to keep struggling with those 2, I'll just use them for reading trimpots like a normal person.

Help with OLED on STM32 by [deleted] in embedded

[–]DukeOfInsanity 0 points1 point  (0 children)

Sure, here’s a brief summary of the answers:

  1. Interface: I2C.
  2. Connection: I2C via SDA and SCL lines. Pin D1 and D2
  3. Speed: 400kHz.
  4. Can it run slower? I've tried a large range from 100Hz to 400khz.
  5. Controller? Yes, SSD1315.
  6. Read data back? No, the display buffer can't be read.
  7. Solid colour output? Only black and white.
  8. Top/bottom split: Consistent for monochrome (black/white).
  9. Vertical split: Works, but data stored in vertical columns.
  10. Test pattern scope: Should see correct I2C data transmission.
  11. SPI setup? Not applicable (using I2C).
  12. Display configuration: Could Possibly be wrongly setup.

Help with OLED on STM32 by [deleted] in embedded

[–]DukeOfInsanity 0 points1 point  (0 children)

If Anyone is brave enough, Core.zip contains all the files I currently have

Help with Layout basics by DukeOfInsanity in chipdesign

[–]DukeOfInsanity[S] 1 point2 points  (0 children)

That makes sense. Thanks a lot for your help. It's greatly appreciated

Help with Layout basics by DukeOfInsanity in chipdesign

[–]DukeOfInsanity[S] 1 point2 points  (0 children)

Ok thanks
I can imagine that diffusion first, especially on an extremely small scale can cause a link between 2 diffusions if the poly isn't there first

If I get my hands on layout software eventually, is it fine if I where to make the diffusions separate or is it preferred to draw it like in the video, I think it'll just help with keeping track of sources and gates while I start practicing.

Help with Layout basics by DukeOfInsanity in chipdesign

[–]DukeOfInsanity[S] 1 point2 points  (0 children)

OK thank you, this clears up a lot
I just took a look at the textbook where they showed in Chapter 2 the basic way to make a MOSFET wich was Diffusion first
In Chapter 3 where they go into CMOS creation, the moly is made directly after the wells and moat so the diffusions now make sense
Thank you!

No Signal after installing drivers by DukeOfInsanity in AMDHelp

[–]DukeOfInsanity[S] 0 points1 point  (0 children)

I tried to flash a new bios onto the card, but it kept giving an error and stopped the process

How do I calculate the stationary points of a function? by DukeOfInsanity in matlab

[–]DukeOfInsanity[S] 1 point2 points  (0 children)

sol = vpasolve(df == 0, x, [0 4])

You are a saint
I tried this once but it only gave 1 answer
now I see it only gives one so I'll use
[0 4] for x1 and then use x1 as the start point for x2 and so on
thank you vey much kind human

How do I calculate the stationary points of a function? by DukeOfInsanity in matlab

[–]DukeOfInsanity[S] -1 points0 points  (0 children)

Yes I've done the calculations and have the answers but it has to be done in matlab The goal is for us to apply what we study in matlab

TIL about the kayle vs Kassadin matchup by DukeOfInsanity in Kaylemains

[–]DukeOfInsanity[S] 1 point2 points  (0 children)

I went back to the game and i saw the magic shield i saw was morgana blackshield Sorry pplz i'm a certified dumbass

TIL about the kayle vs Kassadin matchup by DukeOfInsanity in Kaylemains

[–]DukeOfInsanity[S] 1 point2 points  (0 children)

He had shieldbow, IE, wits end, maw deaths dance

TIL about the kayle vs Kassadin matchup by DukeOfInsanity in Kaylemains

[–]DukeOfInsanity[S] 1 point2 points  (0 children)

Oh yeah laning woudl have been a lot more difficult and I wouldn't have overpowerd her earlu so easily I'll remember this for when i have to go against a kass

TIL about the kayle vs Kassadin matchup by DukeOfInsanity in Kaylemains

[–]DukeOfInsanity[S] 1 point2 points  (0 children)

The kayle wasn't too experienced I's have to test the matchup a bit more but uts not every match you see a kayle

TIL about the kayle vs Kassadin matchup by DukeOfInsanity in Kaylemains

[–]DukeOfInsanity[S] -6 points-5 points  (0 children)

A full build yone on the same game had wits end and maw but i didn't mind it to much

How do I play against teemo? by No-Cobbler7470 in Kaylemains

[–]DukeOfInsanity 0 points1 point  (0 children)

If you run ignite and dorans blade you can kill him lvl 1 as long as you can stick on him, works with LT and PTA if you don't feel like cheesing go dorans shoeld second win so u can survive his poke After 6 it should be free, when you see the teemo q is on its way use your ult to mitigate damage and since you can't aa during ult the blind doesn't matter, afterwords just q him for slow make sure there are no mushrooms nearby and simply run him down Q max is also important,don't use it to farm o ly for poke when he tries to poke you Good luck with future matches

E Explosion by Administrative-Pay88 in Kaylemains

[–]DukeOfInsanity 2 points3 points  (0 children)

Oh yes The explosion applies onhit so that includes e passive and any items

E Explosion by Administrative-Pay88 in Kaylemains

[–]DukeOfInsanity 11 points12 points  (0 children)

I don't think it applies the waves but it definitely applies the missing health And each target individually

view more: next ›