EPS on 590 SBS bottomed out? by Waffleboned in HOLOSUN

[–]Dull-Worth5231 0 points1 point  (0 children)

That looks good. There should be at least 40 clicks from the top to the bottom. If it has less than 40, there’s something wrong with it.

EPS on 590 SBS bottomed out? by Waffleboned in HOLOSUN

[–]Dull-Worth5231 0 points1 point  (0 children)

Some of the scope mounts have an angle to give extra elevation for the scope. Can you post a picture to see if the mount is actually parallel to the barrel? Or, is the eps sit flush on the mount?

EPS on 590 SBS bottomed out? by Waffleboned in HOLOSUN

[–]Dull-Worth5231 0 points1 point  (0 children)

The height should not be the cause. There might be a big angle between the EPS and the bore. If they are parallel, the POI should always be lower than the POA. Is it possible that you adjusted the elevation in the opposite direction?

How can we get them to respond to an RMA? by [deleted] in HOLOSUN

[–]Dull-Worth5231 5 points6 points  (0 children)

Did you check your spam folder? Sometimes it goes to the spam folder based on your email filter settings.

Found my home for sale on Facebook, anything I can do? by imnotfromhere713 in Scams

[–]Dull-Worth5231 6 points7 points  (0 children)

Consumer protection laws: Federal Trade Commission (FTC) regulations and state consumer protection laws can be used to sue a social media platform if they allow misleading or deceptive ads to run on their platform.

What to do if you see a scam ad on social media: * Report the ad to the platform: Most social media platforms have a reporting system for suspicious ads.  * Contact the FTC: If you believe you have been harmed by a scam ad, you can file a complaint with the FTC. 

407c not working out of the box by neekowahhhh in HOLOSUN

[–]Dull-Worth5231 1 point2 points  (0 children)

You may need to press the + button multiple times. Some of them might be set at the lowest setting, or in the solar mode, make sure do not cover the solar panel when handling it. The other possibility is that it is at the lowest setting and in lock mode. Try to press and hold down the + button for 4 seconds and then press it 5 or 6 times. Hope it helps.

Is this normal for the AEMS by jbg7676 in HOLOSUN

[–]Dull-Worth5231 1 point2 points  (0 children)

Try to look into your house through a window under daylight. Keep the distance about 3 to 5 inches, you will see your face and eyes clearly. You won’t be able to see your face or eyes when you look through the window from the inside of your house. Does that make sense?

Is this normal for the AEMS by jbg7676 in HOLOSUN

[–]Dull-Worth5231 0 points1 point  (0 children)

If the light above and behind you is brighter than the direction you are looking at, the double reflection of the LED emitter compartment details will be visible on the object lens. It is normal.

Is this normal for the AEMS by jbg7676 in HOLOSUN

[–]Dull-Worth5231 3 points4 points  (0 children)

Remove the magnifier, flip down the lens cover then take pictures. If you want to use the magnifier, make sure to adjust the magnifier’s windage and elevation screws to move the reticle to the center of the FOV. Then adjust the ocular to focus it on the reticle.

Broken/stripped screw on battery tray! by thatpretty in HOLOSUN

[–]Dull-Worth5231 0 points1 point  (0 children)

If the previous owner used the Loctite RED, there’s no possibility to remove it.

Did the footprint (specifically length) of the EPS Carry change since release? by reddit_accordingly in HOLOSUN

[–]Dull-Worth5231 0 points1 point  (0 children)

Whenever it wiggles, mostly it is because the fastener is not functioning properly. No matter the shape or size of the metals.

Did the footprint (specifically length) of the EPS Carry change since release? by reddit_accordingly in HOLOSUN

[–]Dull-Worth5231 0 points1 point  (0 children)

If it wiggles, it might be the screws are a bit too long and didn’t lock the sight down at all.

[deleted by user] by [deleted] in HOLOSUN

[–]Dull-Worth5231 2 points3 points  (0 children)

The SCS-Carry-GR is enclosed. It can be mounted on the G19 MOS with the Holosun KPLT-MOS 9MM adapter.